Contact Us

DRV5053OAQLPGM

Brand: Texas Instruments
Texas Instruments DRV5053OAQLPGM is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV5053OAQLPGM — Power Management & Signal Chain | Superb Automation

DRV5053OAQLPGM

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV5053OAQLPGM from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV5053OAQLPGM: the 11 mV per mT analog sensor in a TO-92

The DRV5053OAQLPGM is the least sensitive member of the DRV5053 analog family, and it is the only one offered in the through-hole body at this threshold. At 11 mV per mT with a 1 V quiescent output, a 40 mT field moves the output by only 440 mV, which is the point: this part is built for a strong magnet or a long travel, not for a delicate one.

The TO-92 body puts the Hall element about 1 mm above the board, which helps when the magnet has to pass outside the enclosure. The package is three pins, supply, ground and output, and the ammo packing keeps 3000 parts in a strip that a manual or semi automatic insertion machine can feed.

Everything else matches the family: 2.5 V to 38 V supply, 1.8 kHz bandwidth, 35 us power-on, the output stage that sinks 2.3 mA and sources 300 uA, and a Q grade that runs from minus 40 C to plus 125 C.

Key data for the DRV5053OAQLPGM

OutputAnalog, 0.2 V to about 1.8 V, 1 V at zero field
SensitivityMinus 11 mV per mT, negative slope, the lowest in the family
Field rangeAbout 70 mT of travel before the output clips at either end
Supply2.5 V to 38 V, no external regulator, reverse protection to 22 V
Supply current2.7 mA typical at 25 C, 3.0 mA at 125 C
Bandwidth1.8 kHz, which suits a mechanical motion rather than a fast edge
TemperatureMinus 40 C to plus 125 C on the Q grade

Body, packing and marking data

BodyTO-92, three pins, LPG outline, 4.00 mm by 3.15 mm
Packing3000 pieces in ammo pack on the M suffix, 1000 in bulk without it
FinishTin lead finish, moisture level not applicable to the through-hole body
MarkingALOA on the flat face, which identifies the OA die

How the low sensitivity changes the wiring

At 11 mV per mT the output moves slowly, so the reading is dominated by whatever noise sits on the analogue path. That does not make the part worse, it makes the routing of the receiving circuit more important: a short trace, a ground that returns to the controller rather than to the load, and an ADC that averages several samples will recover a clean position.

The negative slope is the other thing to plan for. A south pole at the marked face pulls the output below 1 V and a north pole pushes it above, which is the opposite of the EA option. On a mechanism that was qualified with a positive slope part, swapping in this one inverts every reading.

The bulk option is worth knowing about. The same code without the M suffix is 1000 pieces in a bag rather than a strip, which is fine for a hand build and awkward for any automatic insertion. The addendum prints both rows as active in the TO-92 body.

Where a low sensitivity analog sensor fits

Long travel linear position, lever angle on a machine guard, and magnetic field monitoring where the field itself is the measured quantity rather than a proxy for position are the three uses that suit 11 mV per mT. The wide linear range also helps on a magnet whose field varies with temperature, because the sensor is operating well below saturation.

When the sensor sits on a moving harness, the kitting service page covers how the through-hole parts and the connector are kept together for the build, and the date code management page sets out what to record for a part that may sit in stores between builds.

Questions we get on this code

Can this part measure the field of a small magnet at 5 mm? It can, but the signal will be a few tens of millivolts, which is close to the noise floor of a 10 bit converter on a 3.3 V rail. The higher sensitivity options exist for exactly that case, and the OA part is the wrong choice for a weak magnet.

Is the TO-92 sensitive to lead bending? The Hall element sits about 1 mm above the board inside the package, and bending the leads close to the body can stress the die. The vendor drawings give the minimum bend radius, and a small vice or a lead former is worth the cost on a production line.

One more note on the output stage. The part sinks 2.3 mA and sources only 300 uA, so an ADC input with a low input impedance will load the output asymmetrically and pull the reading down near the top of the range. A buffer or a series resistor into a high impedance input keeps the transfer curve symmetrical.