Contact Us

TPSM53602RDAR

Brand: Texas Instruments
Texas Instruments TPSM53602RDAR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPSM53602RDAR — Power Management & Signal Chain | Superb Automation

TPSM53602RDAR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPSM53602RDAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPSM53602RDAR: 2 A from a 36 V input in a 5 mm square with a 19.5 C per W thermal path

The TPSM53602RDAR is a 36 V input, 2 A step-down module in a 15 pin B3QFN of 5 mm by 5.5 mm by 4 mm, with a shielded inductor and the passives inside the package. What separates it from the small modules is the thermal path: 19.5 C per W junction to ambient on a 75 mm by 75 mm four layer board with 2 oz copper, which is a figure that lets the part deliver 14 W of output at 85 C ambient with no airflow. That is a power module behaving like a converter with its own heatsink, and it is why the part shows up in industrial and telecom equipment rather than in handheld products.

The package has all pins on the perimeter and one large thermal pad, so the board footprint is a simple rectangle with a copper island underneath. The solution needs as few as four external components, and the compensation and the magnetics are already chosen inside the module, which removes the two parts of a converter build that most often pushes a schedule: the loop and the inductor.

Key electrical data on the page

Input range3.8 V to 36 V, turn on at 3.55 V and turn off at 3.05 V, so a 5 V rail can sag and recover
Output1 V to 7 V adjustable at 2 A, with 3 A and 4 A members in the same footprint and pin out
Efficiencyup to 95 percent, and 91 percent measured at 2 A and 25 C ambient
Switchingup to 1.4 MHz, which keeps the module small and moves the ripple above the audio band
Power good107 percent rising fault, 94 percent rising good, 92 percent falling fault, 35 ohm open drain
Soft start4 ms internal, which bounds the inrush into a 66 uF output bank
Thermal19.5 C per W junction to ambient, thermal shutdown at 165 C with recovery at 148 C

Package, marking and reel data

BodyB3QFN RDA, 15 pins, 5.0 mm by 5.5 mm by 4.0 mm, single large thermal pad underneath
Reel1000 pieces on a 330 mm reel, 16.4 mm carrier, 8 mm pitch, quadrant Q1
PocketA0 5.28 mm, B0 5.78 mm, K0 4.28 mm, carrier width 16.0 mm
Finish and moisturenickel palladium gold, level 3 at 245 C, 168 hour floor life
Marking and gradeTPSM53602 on the top, -40 C to 125 C junction, -40 C to 105 C ambient

Rugged numbers that are not on a marketing page

The part is tested to Mil-STD-883D for shock and vibration, which is a qualification that matters on railway and vehicle equipment and is rarely quoted for a power module. The hiccup mode short circuit protection means a shorted output pulls the module into a low duty retry instead of latching, so a backplane that is plugged in wrong recovers when the fault is removed. Start up into a pre-biased output is supported, which matters when a 3.3 V rail is held up by another converter on the same bus and this module has to start without pulling the rail down first.

The 14 W at 85 C figure is the practical ceiling for the part, and it sets what the module can do in a sealed enclosure: at 1.2 V out that is 11.6 A, well above the 2 A rating, so on a low output voltage the current rating binds first and on a 7 V output the thermal rating binds first. A 5 V output at 2 A is 10 W, which leaves margin, and a 7 V output at 2 A is 14 W, which is exactly at the limit and needs the copper area the datasheet assumes.

Buyer questions on the TPSM53602RDAR

Is it pin compatible with the 3 A and 4 A members? Yes. The TPSM53603 and TPSM53604 use the same footprint and pin out, so a board can be laid out once and populated for the current the product needs.

What sets the output voltage? An external divider from the output to the feedback pin. The reference is 1.2 V, and the module compensates itself, so the divider is the only thing the customer changes.

Does the module need an external inductor or compensation? No. The inductor and the compensation are inside the package, which is the reason the external component count is as low as four.

Buying this part through a component supplier

A module at this power level is usually a long life line item, and the 1000 piece reel is a production quantity rather than a prototype one. We supply the RDA code with the level 3 moisture information on the label through date code management, because a 168 hour floor life part that sits out on a bench is a reflow risk. For a programme planning a lifetime buy, last time buy and LTB planning covers the arithmetic, and the power management cross reference lists the 36 V modules we can compare by thermal resistance.