Contact Us

Date Code Management

Date Code Management

Date code is the field on a component label that nobody reads until a build fails, and by then the material is already on the board. A reel received two years ago, a bag opened for a sample run and never resealed, a partial reel poured into a new one during a line change: each of these is a date code problem that shows up later as poor wetting, delamination or an intermittent joint that no one can explain.

Managing it is not a labelling exercise. It is a receiving record, a policy per part class, and a rule for material that passes the window, all written before the first order rather than after the first failure.

Where date code control breaks

The first break is receiving by label. A shipping document says the part, the quantity and sometimes a lot, and the carton is booked in against it. The date code printed on the reel is a different number, and unless someone reads it, the age already in the material never enters the system. A receipt that starts at age eight months gives a two year floor life sixteen months of use, not twenty four.

The second is first in first out in name only. FIFO assumes all stock is in one place and one system. In practice there are partial reels at the line, a sample drawer, a return from a cancelled build, and a second shelf that nobody reconciled. The oldest material is often the material that is hardest to find, which is exactly backwards.

The third is mixing reels. Two reels of one part with date codes five years apart, combined to make a full reel, produce a build whose age cannot be stated afterwards, and the board record points at a lot covering both.

The fourth is bake without a record. Moisture sensitive parts get baked when someone remembers, and the bake is not logged, so floor life restarts without evidence. J-STD-033 asks for exposure and bake to be recorded, not remembered.

The fifth is material the customer supplies. Consigned stock arrives with its own history and is often the oldest material on the floor, because it has been sitting in someone else's store. Without a receiving inspection against the same date code rule, it enters the build unexamined.

A policy per part class

One expiry rule for the whole BOM is unworkable. Different classes age for different reasons and need different controls.

Part classWhat actually agesControl that fitsRecord needed at receipt
Passives and chip resistorsTermination solderability over long storageAge limit with a solderability check on aged stockDate code, pack condition
Electrolytic capacitorsElectrolyte dry out, leakage current driftShorter window, reform or test before useDate code and storage temperature
Moisture sensitive ICsAbsorbed moisture, popcorn cracking at reflowMSL level and floor life tracked, bake at 125 C when exceededMSL, bag seal date, exposure log
Solder paste and adhesivesChemistry, viscosity, shelf life from productionCold chain, use within stated life after thawProduction date and thaw record
Connectors and mechanical partsPlating oxidation, plastic creepAge limit plus a fit check on aged stockDate code, pack condition
RF modules and tuned partsSealing, internal joints, calibration driftAge limit with a functional check before releaseDate code, serial or lot

What the receiving record should carry

Six fields turn the policy into an auditable fact: the date code as printed, the maker and full part number, the pack condition on arrival, the MSL and seal date where it applies, the quantity counted, and the storage location. Every later question, whether an aged release or a customer return, is answered from that record or not at all.

The count matters as much as the code. Components are counted by X-ray on receipt at SUPERB PCBA rather than accepted by label, and the count makes a partial reel visible before it becomes a shortage.

How SUPERB PCBA carries date code through a build

Markings and date codes are compared with maker data on receipt, and parts that carry provenance risk are opened and checked. Aged stock is verified for solderability before it is released to a kit. Moisture sensitive parts are baked at 125 C to J-STD-033 and held under ESD S20.20 in an SMT area at ISO 8, 22 plus or minus 3 C and 45 to 65 percent relative humidity, so the floor life that the record depends on is a controlled condition rather than an assumption about the room.

On the line, seven SMT lines place down to 01005 with 3D SPI on paste volume, 3D AOI plus DIP AOI, X-ray in 2D and CT to IPC-7095 with voiding below 5 percent, twelve zone reflow on SAC305 with nitrogen below 500 ppm, ICT and functional test, seventeen process steps and ten QC stations under IPC-A-610 Class 2 and Class 3, ISO 9001, and ISO 13485 for medical programs. Verified lots carry a 730 day warranty. The date code travels with the lot on the build record, so a unit returned in year three resolves to the reel it came from.

The pieces around it are on incoming inspection plan for the sampling side, excess inventory management for material that has passed its window, and pre-shipment component inspection for the check before boards leave.

Aged material: release, bake or retire

Age alone does not condemn a part. The decision has three outcomes, each needing a name on it. Release means a check was done, passed and written down. Bake means floor life was reset under J-STD-033 and the exposure and bake were logged. Retire means the material leaves the shelf and the record says why.

Date code management questions

What date code is acceptable on arrival?

Set it in writing per part class before the first order. A common rule is a stated maximum age at receipt plus a stated minimum remaining life at the point of use, and the second number is the one that protects a long program. Anything older is a written concession, not a silent acceptance.

Does baking restore a part completely?

It restores the moisture state, not the shelf life. A part that has been stored for years still has aged terminations and, on some classes, drifted parameters, which is why the solderability and functional checks sit alongside the bake rather than being replaced by it.

How does consigned material fit the policy?

It goes through the same receiving record. The age is often the surprise, because material held in another store has been ageing without being anyone's line item. Where the age is outside the policy, the decision belongs to the customer in writing, before the material is kitted. The handover side is described on kitting service.

Next step

Send the BOM with the date code policy your quality team already uses, or the part classes you want one for. The reply states, per class, the age accepted at receipt, the checks applied to aged stock, the bake and storage conditions, and the record fields you will be able to audit on the first lot.