UCC27201ADDAR
Product Specifications
UCC27201ADDAR
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC27201ADDAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC27201ADDAR: TTL thresholds and 18 V of negative tolerance on the switch node
The UCC27201ADDAR is the A revision of the TTL input half bridge driver, with a 120 V bootstrap, 3 A source and sink, 22 ns propagation delay and 1 ns of delay matching. Against the original UCC27201 the A revision adds two things that matter on a real board: the switch node tolerates minus 18 V instead of minus 5 V, and the input structure has a higher ESD rating. On a 100 V bus with a fast MOSFET and a few nanohenries of source inductance, the switch node rings well below ground on every turn-off, and the extra negative tolerance is the difference between a driver that survives and one that fails in the first week of a reliability run.
The TTL thresholds are the second reason to pick this part over the UCC27200A. A 3.3 V controller driving a 12 V driver needs an input threshold that is referenced to the logic rail, not to the driver supply, and TTL compatible parts accept 3.3 V logic directly. The bootstrap diode is inside at 0.65 V forward drop and 0.65 ohm, the part is specified from minus 40 C to 150 C, and the two channels switch within 1 ns of each other.
Key electrical data for the UCC27201ADDAR
| Topology | Half bridge driver, independent inputs, TTL compatible thresholds |
| Voltages | 120 V maximum boot, 20 V maximum VDD, minus 18 V absolute maximum on the HS pin |
| Drive | 3 A sink and 3 A source, 8 ns rise and 7 ns fall with a 1000 pF load |
| Timing | 22 ns propagation delay, 1 ns delay matching, UVLO on both drivers |
| Bootstrap | On chip diode, 0.65 V forward drop, 0.65 ohm series resistance |
| Grade | Specified -40 C to 150 C junction on the active row |
Package, marking and reel data
| Body | DDA, 8 pin SO PowerPAD, same land pattern as the UCC27200 family |
| Reel | 2500 pieces on a large reel for the .A row |
| Finish | NIPDAU or NIPDAUAG, level 1 at 260 C with unlimited floor life |
| Status | The plain UCC27201ADDAR row is marked Obsolete, the .A row is active and in production |
The obsolete plain row and what it means for a build
The addendum lists UCC27201ADDAR as Obsolete with no quantity and no plating, and the .A row as active at 2500 pieces. Both rows share the body, the pinout and the function, so a build that has the plain code on its approved vendor list can move to the .A row without a board change, but the change has to be recorded because the temperature specification and the negative voltage tolerance are not the same across the whole family. A broker offer that names the plain code is either old stock or a relabelled part, and both need the date code and the X-ray check before they go to a line.
The functional case for the part is unchanged. Solar micro inverters, telecom rectifiers and battery test equipment use it to drive a half bridge at 48 V to 100 V, and the 18 V negative tolerance on the switch node is what allows a board with a slightly longer gate loop to still pass a surge test. The cost of that tolerance is nothing on the board: the land pattern is the same as the earlier code. Our obsolete part cross reference hub page lists the active rows we quote for this family.
Buyer questions on the UCC27201ADDAR
Can the .A row replace the plain row directly? Yes on the board, no on the paperwork. The land pattern and the pinout match, but the .A row is the only active row and the qualification record has to be updated to the new code.
Is minus 18 V a continuous rating? It is an absolute maximum on the HS pin for the transient the switch node produces, not a DC operating point. The board still has to keep the average switch node voltage inside the 120 V bootstrap limit.
Does the TTL input work with a 5 V controller? It does, and it also works with 3.3 V logic, which is the reason to choose this row over the CMOS threshold version when the controller runs from a lower rail than the driver.
Availability and cross reference
We quote the .A row by default for this code and state the status of the plain row on the quotation. The reel is 2500 pieces at level 1 with unlimited floor life, so a partial reel can go back on the shelf without a bake. For a build that has been running the UCC27200 in the same socket, the TTL threshold change is the one item that needs a review, and our pin to pin cross reference page documents the family that shares the land pattern.