TPSM82822ASILR
Product Specifications
TPSM82822ASILR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPSM82822ASILR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPSM82822ASILR: 2 A of forced PWM for a rail that must not change its ripple
The TPSM82822ASILR is the adjustable, forced PWM member of the 2 A MicroSiP group. It uses the same 2.0 mm by 2.5 mm by 1.1 mm ten pin body and the same DCS-Control loop as the power save versions, and the difference is that it never enters PFM: the converter switches continuously at about 4 MHz from no load to 2 A. That costs quiescent current and buys a ripple that does not change shape with the load, which is what an analog front end, a clock buffer or a radio synthesizer needs from its supply.
The output is set by an external divider from 0.6 V to 4 V, so the same order code covers a 0.9 V core rail, a 1.8 V I/O rail and a 3.3 V analog rail. The feedback pin sits at 1.2 V nominal with 1 percent accuracy, and because the loop is internally compensated the divider is the only thing the customer chooses. That is a useful property in a product family: one part number, several rails, one BOM line.
Key electrical data on the page
| Input and output | 2.4 V to 5.5 V in, 0.6 V to 4 V out by external divider, 2 A continuous |
| Mode | forced PWM at all loads, so the switching frequency and the ripple stay fixed |
| Switching | 4 MHz nominal, DCS-Control, no external compensation network |
| Reference | 1.2 V with 1 percent accuracy, 1.188 V to 1.212 V over the operating range in PWM |
| Dropout | 90 milliohm typical and 120 milliohm maximum at 2 A in 100 percent duty mode |
| Power good | open drain window comparator, 5.5 V maximum pull up, 1 mA sink |
| Protection | hiccup short circuit, thermal shutdown, output discharge when disabled |
Package, marking and reel data
| Body | uSiL SIL, 10 pins, 2.0 mm by 2.5 mm by 1.1 mm, the same pad as the other 8282x members |
| Reel | 3000 pieces on a 330 mm reel, 8.4 mm carrier, 4 mm pitch, quadrant Q1 |
| A0 2.25 mm, B0 2.75 mm, K0 1.25 mm, carrier width 8.0 mm | |
| Box | 383 mm by 353 mm by 58 mm, one reel per box |
| Ordering note | the A in the seventh position marks the forced PWM die, not a revision of the silicon |
Where the continuous conduction matters
A converter in PFM at light load produces a burst of switching followed by a pause, and the output voltage rides up and down by a few millivolts at an audio rate during the pause. On a digital rail that is invisible. On a 1.2 V reference for an ADC, or on the supply of a low phase noise oscillator, it appears as a sideband that moves with the load pattern, and it is very hard to filter because it is not at a fixed frequency. Forced PWM removes the problem at the source, at the cost of a quiescent current that is milliamps rather than microamps.
That is the honest trade on this order code. A battery product that sleeps for hours wants 82822 with power save; an instrument that runs from a wall adapter and cares about a clean spectrum wants 82822A. Both are the same pad and the same external components, so a board can carry a stuffing option and the product can move between the two without a board change. The 5.5 V input ceiling means the rail comes from a 3.3 V or 5 V bus rather than from a 12 V one, which is the usual arrangement behind a first stage.
Buyer questions on the TPSM82822ASILR
What is the difference between 82822 and 82822A? Only the light load behaviour. The plain 82822 enters power save and draws microamps at no load, the A version stays in continuous conduction at 4 MHz and draws milliamps. The pin out and the external parts are identical.
Can the output be sequenced with another rail? Yes, through the enable pin and the power good flag. There is no tracking pin on this family, so sequencing is a delay chain rather than a ramp ratio.
Does forced PWM change the efficiency at full load? No, at 2 A both versions run in continuous conduction and the efficiency is the same. The difference only appears below about 100 mA.
Buying this part through a component supplier
The A suffix is one character in a seven digit code, and it changes the standby current by three orders of magnitude, so it belongs on the drawing and on the reel label. We supply the A and plain members as separate codes with the marking recorded through date code management. When a programme is choosing between them late in a schedule, how to verify a drop in replacement covers the measurements that show the difference, and the power management cross reference lists the other 2 A modules on the same pad.