UCC21732QDWRQ1
Product Specifications
UCC21732QDWRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC21732QDWRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC21732QDWRQ1: 10 A of gate drive with 270 ns overcurrent protection for a 2121 V silicon carbide bridge
The UCC21732QDWRQ1 is an automotive qualified single channel isolated gate driver built for silicon carbide MOSFETs and IGBTs up to 2121 V peak. It delivers plus and minus 10 A peak with a split output, so the turn-on and turn-off paths can be set independently, and it holds a 5.7 kVRMS isolation barrier with 150 volts per nanosecond of common mode transient immunity and 12.8 kVPK of surge immunity. The propagation delay is 130 ns maximum, which is the number that sets the dead time on a bridge switching above 50 kHz.
What makes it more than a driver is the protection set. A 270 ns overcurrent response with an external active Miller clamp, a two level turn-off sequence that lowers the gate to an intermediate level before shutting off completely, and an isolated analog to PWM sensor that carries a temperature reading from an NTC, a PTC or a thermal diode back across the barrier. The fault pin reports an overcurrent event and the reset pin clears it, so a controller can distinguish a transient from a real fault without an extra isolated signal path.
Key electrical data for the UCC21732QDWRQ1
| Drive | Plus and minus 10 A peak with a split output, 33 V maximum between VDD and VEE |
| Timing | 130 ns maximum propagation delay, 270 ns overcurrent detection response |
| Isolation | 5.7 kVRMS barrier, 12.8 kVPK surge, CMTI 150 V per nanosecond minimum, 1.5 kVRMS working voltage |
| Sensing | Isolated analog to PWM output for NTC, PTC or thermal diode, DC link or phase voltage |
| Protection | Fast overcurrent and short circuit detection, active Miller clamp, two level turn-off, input and output UVLO with RDY |
| Grade | AEC-Q100 grade 1, -40 C to +125 C ambient, HBM level 3A, CDM level C3 |
Package, marking and reel data
| Body | DW, 16 pin SOIC, 10.30 mm by 7.50 mm |
| Reel | 2000 pieces on a large reel for this code |
| Finish | NIPDAU on the .A row, which is also the row that carries the level 3 at 260 C and 168 hour floor life |
| Status | The plain row is listed with plating and moisture as Call TI, the .A row is the one with published data |
The Miller clamp and the two level turn-off in practice
A silicon carbide MOSFET turns on faster than a silicon IGBT and its threshold sits lower, so a bridge leg that switches hard couples a displacement current through the Miller capacitance of the device that is meant to be off. The clamp holds that gate at the source through a low impedance path below the threshold, and it does so without waiting for the driver to decide. Without it, a 1200 V bridge running at 20 kV per microsecond will show spurious turn-on pulses on the low side device during every high side transition.
The two level turn-off matters on a short circuit. Dropping the gate straight to the negative rail with 10 A of drive produces a current commutation that can exceed the device's safe operating area; stepping the gate to an intermediate level for a short window and then to the negative rail spreads the energy. The 270 ns detection response is the budget the controller has before the fault current reaches its limit, so the shunt and the comparator around the driver have to be matched to it rather than chosen independently. Our defense grade components page covers the high reliability builds where this driver class is used.
Buyer questions on the UCC21732QDWRQ1
Does the isolated sensor need a separate amplifier? No. The module converts the analog reading to a PWM stream across the barrier, and the controller recovers the value by measuring the duty cycle, so no isolated amplifier and no second barrier are needed.
Is the 2121 V rating an operating voltage or a withstand? It is the peak operating voltage the vendor specifies for the SiC and IGBT devices the part is built to drive. The barrier withstand is 12.8 kVPK surge, which is a different figure and should not be substituted for it.
Which row carries published plating data? The .A row. The plain UCC21732QDWRQ1 row is published with plating and moisture marked Call TI, so a build that needs a documented reflow window should be quoted on the .A row.
Availability and cross reference
The code ships 2000 pieces per reel and the .A row carries the level 3 moisture class at 260 C with a 168 hour floor life. For an automotive or defense build the lot has to be traceable to the reel, and the X-ray and bake records travel with the shipment. Our sourcing audit trail page describes the record set we keep for isolated drivers at this voltage class.