Contact Us

TPSM86638RCGR

Brand: Texas Instruments
Texas Instruments TPSM86638RCGR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPSM86638RCGR — Power Management & Signal Chain | Superb Automation

TPSM86638RCGR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPSM86638RCGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPSM86638RCGR: 6 A from a 24 V bus in a 5 mm by 5.5 mm HotRod body

The TPSM86638RCGR is a 6 A synchronous buck power module that takes 4.5 V to 28 V in and delivers 0.6 V to 13 V out, with the MOSFETs, the shielded inductor and the basic passives inside a 19 pin B3QFN HotRod package measuring 5.0 mm by 5.5 mm. The 638 suffix is the forced continuous member: it holds a pseudo-fixed frequency at light load and keeps the output ripple flat, where the 637 runs Eco-mode for higher light load efficiency. Both are rated to a 150 C junction, which is 25 C above the module family above it and is the reason this part shows up in sealed enclosures.

Two switching frequencies are selectable, 800 kHz and 1200 kHz, and the choice is made at start-up by the state of the mode pin after the internal 5 V rail comes up. The lower frequency buys efficiency at 24 V in and 5 V out, the higher one shrinks the inductor ripple and the output capacitance. Soft start is set by a capacitor on the SS pin, the part has a built-in output discharge, and the protection set is non-latching overvoltage, undervoltage, overcurrent, overtemperature and UVLO.

Key electrical data for the TPSM86638RCGR

Input range4.5 V to 28 V, UVLO wakes at 4.2 V typical with 550 mV of hysteresis
Output0.6 V to 13 V adjustable, reference 0.6 V at 1 percent from 25 C
Current6 A continuous, duty cycle up to 98 percent
Switching800 kHz or 1200 kHz selectable at start-up through the mode pin
Quiescent45 microamps no load, 3 microamps shutdown, soft start set by an external capacitor
ProtectionNon-latching OV, UV, OC, OT and UVLO, power good output, output discharge on disable

Package, marking and reel data

BodyRCG, 19 pin B3QFN HotRod, 5.00 mm by 5.50 mm
Reel1000 pieces on a 330 mm reel, 16.4 mm carrier, pocket 5.28 by 5.78 by 4.28 mm, quadrant Q1
FinishNIPDAU, level 3 at 250 C peak with a 168 hour floor life
GradeJunction rated -40 C to 150 C, industrial and medical applications listed by the vendor

Why the 250 C moisture level matters on this body

Most of the modules in this catalogue carry a 260 C reflow rating. This one is published at 250 C peak with a 168 hour floor life at level 3, which is still inside a standard lead free profile but leaves less headroom, and the floor life means the reel has to be used or baked within a week of opening. On a production line that opens a reel for a partial build and puts it back on the shelf, that rule is the difference between a good joint and a delaminated package, and it is not visible in the part number.

The thermal case at 24 V in and 5 V out with 6 A is about 1.5 W inside the package, and the HotRod body conducts most of that into the board through the thermal pad, so the copper under the part carries the thermal path. Four thermal vias into a ground plane and 100 mm squared of copper on the bottom layer hold the junction at roughly 105 C in a 60 C ambient, which is inside the 150 C rating with margin. Our component lead time solutions page covers the reel and bake rules we apply to this family.

Buyer questions on the TPSM86638RCGR

Can the frequency be changed after the board is built? No. The mode pin is read once after the internal rail comes up, so the frequency is fixed by the pin state at start-up and a change requires a board change, not a software setting.

Does the 1000 piece reel mean this is a low volume part? It means the vendor publishes 1000 pieces per reel for this body, not that the part is scarce. Two reels cover a 2000 piece build and the carrier is 16.4 mm, so the feeder and the splice tape have to suit that width.

Is this part suitable for a 48 V telecom bus? No. The input is rated to 28 V, so a 48 V rail needs a different family. It suits 12 V, 19 V and 24 V buses, which is what the vendor states in its application list.

Availability and cross reference

The 638 and the 637 share the body, the reel and the pinout, so the choice between them is a light load decision rather than a board decision. We hold both against forecast and flag the 250 C reflow rating on the packing list, because an assembler running a profile tuned for 260 C parts will not notice the difference until the yield report arrives. Parts that come from a broker with no reel label are the ones to reject on this body, and our incoming inspection plan sets out what we check before a lot goes to the line.