Contact Us

TPSM828303ARDSR

Brand: Texas Instruments
Texas Instruments TPSM828303ARDSR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPSM828303ARDSR — Power Management & Signal Chain | Superb Automation

TPSM828303ARDSR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPSM828303ARDSR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPSM828303ARDSR: 3 A down to 0.5 V from a 2.25 V input, with 55 milliohm of dropout

The TPSM828303ARDSR is the 3 A member of the TPSM82830x family, a 2.25 V to 5.5 V input module with an adjustable output from 0.5 V to 4.5 V and a 2 MHz switching frequency. The number that separates it from the other small modules is the dropout resistance: 55 milliohm in 100 percent duty mode, which keeps a 1.2 V rail in regulation from a 1.3 V input and lets a lithium pack run down to the end of its curve without a separate bypass switch. The 1 percent feedback accuracy over the full -40 C to 125 C junction range is the second number that matters, because a 0.5 V rail with 5 percent tolerance is not a rail at all.

The family is built for emission: the MagPack and QFN bodies shield the inductor, the die carries on-chip noise filtering capacitors, and the package is specified to support CISPR11 and CISPR32 limits. The mode pin selects power save or forced PWM at any time during operation, so a product can start in continuous conduction and drop into power save when the controller decides, without a reset.

Key electrical data on the page

Input and output2.25 V to 5.5 V in, 0.5 V to 4.5 V out adjustable, 3 A continuous
Accuracy1 percent feedback voltage accuracy from -40 C to 125 C junction
Dropout55 milliohm in 100 percent duty mode, so a 1.2 V rail holds from a 1.3 V input
Switching2 MHz fixed, DCS-Control with a fast transient response and a small output capacitor
Quiescent7 uA operating in power save mode, with the mode pin available to force PWM instead
Soft startinternal, about 300 us on the RDS body per the device options table
Protectionhiccup over current and over voltage, combined with thermal shutdown

Package, marking and reel data

BodyQFN-FCMOD RDS, 9 pins, 3.0 mm by 3.0 mm, shielded inductor and a single thermal pad
Reel3000 pieces on a 330 mm reel, 17.6 mm carrier, 8 mm pitch, quadrant Q2
PocketA0 3.30 mm, B0 3.30 mm, K0 2.25 mm, carrier width 12.0 mm
Finish and moisturetin, level 3 at 260 C, 168 hour floor life
Marking and gradeTM8303 on the top, rated -40 C to 125 C junction

Why 0.5 V and 1 percent go together

Sub 1 V rails are used for FPGA cores, DDR4 and DDR5 terminations and the newer low voltage memory interfaces, and at 0.6 V a 20 mV error is 3 percent of the rail. A module that holds 1 percent over temperature gives the board engineer room to spend the rest of the error budget on the load and the copper. The 55 milliohm dropout is the other half of the same story: a DDR termination rail has to hold its value while the input moves, and a module that needs 300 mV of headroom cannot do that from a 1.35 V supply.

The mode pin is worth planning even if the product never uses power save. Leaving it floating is not an option, and a pin tied low that later needs to be high is a board respin. A zero ohm link or a spare GPIO costs nothing on the board and keeps the option open. The power good output is a window comparator, so it reports an overvoltage as well as a droop, which matters on a memory rail where an overvoltage damages the load faster than a droop does.

Buyer questions on the TPSM828303ARDSR

What is the difference between the RDS and VCB bodies? Both are 3 mm class QFN parts with the same silicon and the same 3 A rating. The RDS body is the nine pin package at 3000 per reel, the VCB body is a ten pin package at 2500 per reel, and the soft start time differs between specific order codes.

Can the output go below 0.5 V? No. 0.5 V is the reference voltage and the floor of the adjustable range. A lower rail needs a different part with an internal reference below that.

Is the mode pin safe to change while running? Yes. The datasheet allows the mode to be changed during operation, and the loop settles within a few switching cycles. The rail does not glitch during the change.

Buying this part through a component supplier

The 82830x family carries several order codes that differ only in body and soft start time, so the purchase order needs the full string and not the first six digits. We supply the RDS code with the finish and moisture level on the label through date code management, because a level 3 part at 168 hours is a reflow risk if it sits out. When a programme moves between the two bodies, pin to pin cross reference shows what changes on the pad, and incoming inspection plan covers the checks that catch a body mix up at goods in.