Contact Us

TPS7A5201QRGRRQ1

Brand: Texas Instruments
Texas Instruments TPS7A5201QRGRRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A5201QRGRRQ1 — Power Management & Signal Chain | Superb Automation

TPS7A5201QRGRRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A5201QRGRRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A5201QRGRRQ1: 2 A automotive LDO, 0.8 V to 5.2 V adjustable, 4.4 microvolt noise, VQFN-20

TPS7A5201QRGRRQ1 is a low noise linear regulator that sources 2 A with 115 mV of dropout, takes its bias from a higher rail so the pass element can be driven fully on, and holds 0.5 per cent accuracy over line, load and temperature in a VQFN-20 body of 20 pins. The output is set by a resistor divider anywhere from 0.8 V to 5.2 V, and the input works from 1.1 V to 6.5 V when the bias pin is supplied from a rail at least 1.5 V above the output. Output noise is 4.4 microvolt rms and rejection is 40 dB at 500 kHz, which is why the part appears in front of converters, radios and clock circuits rather than behind a switching regulator alone. An open drain power good output and an adjustable soft start complete the pin set.

Order code and package

TPS7A5201QRGRRQ1Active, VQFN (RGR) body, 20 pins, 3000 pieces on a 330 mm reel, marking A5201
TPS7A5201QRGRRQ1.AActive, same body and same 3000 piece reel, material row at MSL Level-2-260C-1YEAR
TPS7A5201WQRTKRQ1the same silicon in the RTK body with a wettable flank for optical inspection
Temperature rangeminus 40 to 150 degrees junction, temperature grade 1 for automotive use
QualificationAEC-Q100 grade 1, with the extended junction range printed on the orderable rows

Electrical parameters that decide the application

Input voltage1.4 V to 6.5 V without the bias rail, 1.1 V to 6.5 V with it
Output voltage0.8 V to 5.2 V, set by an external divider
Output current2 A maximum
Dropout115 mV maximum at 2 A with the bias rail on the automotive grade part
Accuracy0.5 per cent over line, load and temperature
Noise and rejection4.4 microvolt rms from 10 Hz to 100 kHz, 40 dB rejection at 500 kHz
Quiescent currentin the low milliamp range with the bias rail present, higher without it
Soft start and power goodadjustable ramp with an external capacitor, open drain power good output

Family variants and how they differ

TPS7A5201-Q1automotive grade, 115 mV dropout at 2 A, the string on this page
TPS7A52the industrial grade part with the same function and 65 mV of dropout at 2 A
TPS7A8400a 3 A member of the same low noise family in a 20 pin body
Bias pinsupplies the gate drive so the pass element can be driven fully on with a low input voltage
Body optionsRGR with standard flanks and RTK with wettable flanks for automated optical inspection

Points to check before this part goes on a BOM

The bias rail is what makes low dropout possible and it is also the first question on a quote. With a bias supply at least 1.5 V above the output, the pass element is driven from that rail and the dropout falls to 115 mV. Without it, the part still works but the dropout is higher and the input floor is 1.4 V rather than 1.1 V. A board that has no rail above the output cannot use the low dropout figure, and that changes the whole power tree.

Four point four microvolts is measured in a defined band. The number applies from 10 Hz to 100 kHz with the recommended output capacitor and a noise reduction capacitor on the NR pin. Removing the NR capacitor raises the noise well above the headline and a board that leaves the pin open will not measure the published figure. The pin is not optional for a low noise application.

Automotive grade costs dropout in this family. The industrial member of the same family specifies 65 mV at 2 A and the automotive grade part specifies 115 mV. The difference comes from the pass element and the qualification margins, not from a different topology. A board that was qualified on the industrial figure and then moved to grade 1 loses 50 mV of headroom, which is enough to matter on a 1.1 V rail.

A 1.1 V input with a 0.8 V output at 2 A is a difficult operating point. The regulator is 300 mV from dropout, so a 5 per cent dip in the input puts it into dropout and the output follows the input. That is acceptable for a post regulator behind a switching rail with a defined tolerance, and it is a trap when the input is a battery that sags. The input tolerance and the dropout headroom have to be added together before the part is chosen.

Two amps in a 20 pin body needs the pad soldered to copper. At 2 A with a 0.5 V drop the part dissipates 1 W, and the junction to ambient resistance of the package is a few tens of degrees per watt only when the exposed pad is connected to a copper area with vias. In a hot automotive enclosure the thermal calculation, not the current rating, decides whether the part is usable.

The power good output is open drain and needs a pull up that is alive early. It reports the output as valid after the soft start ramp completes, and it is used to hold a downstream converter off. If the pull up is on the rail being monitored, the signal cannot come up before the rail, so the pull up belongs on the always-on supply.

Soft start is set by a capacitor and it protects the upstream converter. A 2 A load step at power up is a large current for a small buck feeding this rail, and the adjustable ramp keeps the demand inside what the upstream can supply. A board that leaves the soft start pin open gets the fastest ramp the part allows, and the current limit of the upstream converter engages instead.

Grade 1 at 150 degrees junction is not the same as 150 degrees ambient. The orderable rows state a junction range of minus 40 to 150 degrees, and the ambient a module can tolerate depends on the dissipation and the board. A customer who reads 150 degrees as an ambient rating will build a product that runs at the edge of the thermal shutdown, and the offer should say junction explicitly.

Rejection of 40 dB at 500 kHz is the number for a switching input. A converter running at 500 kHz puts its ripple at that frequency, and 40 dB takes 100 mV of ripple down to 1 mV. Below 100 kHz the rejection is much higher, so the part is most useful behind a high frequency switcher, which is where most of these rails sit.

What to confirm before this part goes on a purchase order

Name the bias rail and its voltage relative to the output. The 115 mV dropout only exists with a bias at least 1.5 V above the output, and without it the part is a different regulator.

Give the ambient temperature and the copper area under the pad. The current rating is not the limit in a hot enclosure; the thermal resistance and the dissipation are.

Where this order code fits

It cleans a 1.1 V to 5 V rail in front of an ADC, a SerDes, a radio or a clock circuit in an automotive or instrumentation product, where switching ripple on the supply would show up in the measurement. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Does it need a bias supply? Not to function, but to reach its dropout figure. Without a bias rail the input must be 1.4 V or more and the dropout is larger. With a bias rail 1.5 V above the output the input can go down to 1.1 V and the dropout is 115 mV at 2 A.

What is the noise reduction pin for? It filters the internal reference. A capacitor from that pin to ground lowers the output noise below the 4.4 microvolt figure and improves rejection at low frequency. Leaving it open gives a working regulator with more noise than the data sheet headline.

Can it be used as a post regulator behind a buck converter? That is its main application. The buck provides the headroom and the efficiency, and this regulator removes the switching ripple and the low frequency noise that would otherwise reach an ADC, a SerDes or a radio. The input capacitor and the physical distance between the two stages decide how much of the ripple from the buck actually arrives.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.