Contact Us

BQ24172RGYR

Brand: Texas Instruments
Texas Instruments BQ24172RGYR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ24172RGYR — Power Management & Signal Chain | Superb Automation

BQ24172RGYR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ24172RGYR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ24172RGYR: 4 A switch mode charger for one to three cells with an adjustable regulation voltage

BQ24172RGYR is a synchronous buck charge controller with the FETs inside, taking 4.5 V to 17 V in and regulating a pack voltage set by an external divider in a VQFN body of 24 pins. The bq2417x family charges from a DC source as high as 17 V, including a car battery, and the input overvoltage limit is set by a resistor on OVPSET rather than fixed. The AVCC, ACP and ACN pins are rated to 30 V so a high voltage source at the connector does not damage the die. The RGY body is 5.50 mm by 3.50 mm and thin enough to sit under a shield can.

Order code and package

BQ24172RGYRVQFN RGY, 24 pins, 3000 pieces on a large reel, NIPDAU, Level-2-260C-1 YEAR, marking BQ24172
BQ24172RGYTsame body, 250 pieces on a small reel
BQ24172RGYRG4the green row of the same body and reel
BQ24170RGYRthe sibling that regulates 4.2 V per cell through the CELL pin, 2.5 A maximum charge rate
Body size5.50 mm by 3.50 mm, twenty four pins, exposed pad for the switch node return
Temperatureminus 40 to plus 85 C on every published row of this body

Electrical parameters that decide the application

Input range4.5 V to 17 V operating, with AVCC, ACP and ACN rated to 30 V absolute
Charge voltage accuracyplus or minus 0.5 per cent, set on this member by an external divider on FB
Charge current accuracyplus or minus 4 per cent, set by the voltage on ISET
Maximum charge rate4 A on this member against 2.5 A on the BQ24170
Precharge threshold1.43 to 1.47 V on the FB pin, 1.45 V typical, with 25 ms of deglitch
Recharge50 mV below regulation on the FB pin, a 35 to 65 mV window, against 100 mV on the fixed voltage sibling
REGN regulator5.7 to 6.3 V, 6.0 V typical, current limited and used to drive the high side gate
Sleep threshold50 to 150 mV of input above the sense node, 90 mV typical, with 200 mV of hysteresis
Switchingcycle by cycle current limit, internal soft start in eight steps, integrated loop compensation
Termination250 ms of qualification before the cycle ends, so a load pulse does not terminate a charge

Family variants and how they differ

BQ24172 against BQ24170the 70 divides the pack voltage internally from the CELL pin and the 72 takes an external divider, which is what makes the 72 the adjustable member
4 A against 2.5 Athe two members differ in the charge current ceiling, and the inductor and the sense resistor have to be chosen for the member on the board
OVPSET against a fixed tripthe input overvoltage point is set by a resistor, so a 12 V adapter and a 24 V adapter can share one board with a different resistor
1 cell against 3 cellsone board can cover a single cell or a three cell pack by changing the divider, which is why this member is used across a product family
System to battery against system to packwith a non removable pack the system can sit directly on the battery, and the pack then supplements the load when the adapter is overloaded
RGY against the smaller bodiesthe 5.5 by 3.5 mm body carries the two gate drivers and the sense amplifier, so the thermal path is through the pad rather than the leads

Points to check before this part goes on a BOM

The divider on FB sets the pack voltage and nothing else does. There is no internal tap on this member, so the regulation point is whatever the two resistors produce and the tolerance of those resistors adds to the 0.5 per cent of the part. A 1 per cent pair gives about 1.5 per cent at the pack, which is fine for a three cell pack and marginal for a single cell where 50 mV is a visible capacity difference.

The 17 V input rating is not a 24 V rating. A car battery during a load dump goes well above 17 V, and the pins survive 30 V but the converter does not regulate there. The input overvoltage comparator turns the FETs off above the OVPSET point, so the pack is protected but the system is not charged, and a product that must run during a load dump needs a front end clamp rather than a higher resistor.

The recharge threshold on this member is set on the feedback pin, not on the pack. The window is 35 to 65 mV on FB, 50 mV typical, which at a 12.6 V pack is about 430 mV of pack voltage. The fixed voltage sibling uses 100 mV on the sense node instead, so the two members restart at different points and a pack moved from one board to the other shows a different state of charge on the adapter.

Precharge is what recovers a deeply discharged pack. The part holds 25 mA or so into a cell below 1.45 V on FB, and the transition to fast charge is deglitched for 25 ms. A pack that has been in storage for a year needs that phase, and a charger that skips it because the pack was replaced while the adapter was connected will push the full current into a sulphated cell.

The inductor carries the full charge current plus half the ripple. The document states that the saturation current has to exceed the charge current plus half the ripple, and a 4 A build with a 30 per cent ripple needs an inductor rated above 4.6 A. A part chosen for 4 A exactly saturates on the first load step and the symptom is a charger that resets rather than one that runs hot.

Sleep mode is decided by the input to sense difference. The part compares the adapter voltage against the sense node and drops to sleep below 90 mV of difference, which is what stops a reverse current into an adapter that has been unplugged but still sits on the rail. The 200 mV of hysteresis keeps it from chattering at the boundary.

Where the board goes wrong

The sense resistor and the inductor are the pair that decide the loss. A 10 milliohm sense resistor at 4 A dissipates 160 mW, which is acceptable, but a part with 5 per cent tolerance moves the input limit by the same amount and the adapter then either collapses or runs below its rating.

The second fault is the gate drive for the input FETs. The charge pump on this part drives an n-channel ACFET and RBFET, and a FET with too much gate charge slows the turn on enough that the inrush trips the adapter. The 4 kohm resistor the document places in series with the BATFET gate is there for the same reason and is often left out.

What to ask a supplier for

Ask for the reel size with the order code, because the same string is published at 3000 on a large reel and 250 on a small reel and the small reel is a prototype item. A production line that receives small reels loses more time in changeovers than the parts save.

Ask also for the date code and the moisture level. This body is printed at Level 2 with a one year floor life, so a reel that has been open through a humid season needs a bake before reflow, and a supplier who cannot state the level is quoting from a secondary source.

Where this order code fits

Notebook and handheld terminal battery packs, portable instruments with two or three series cells and industrial equipment that charges from a 12 V or 19 V rail use this family. The adjustable regulation point is what makes one board serve a family of packs at 8.4 V, 12.6 V and 16.8 V without a second board. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

How is the charge current set? By a voltage on the ISET pin, with a resistor divider from REGN or from a reference. The document gives the transfer and a 25 per cent window on the ISET falling threshold, which is why a build usually sets the current with a divider from a regulated source rather than from the input rail.

Can the part charge a pack while the system runs? Yes. The system is connected to the pack node through the BATFET path, and when the adapter is overloaded the pack supplements the load. That is why the part is used with a non removable pack, where the system and the battery share one node and the adapter current limit decides the split.

What sets the input current limit? The sense resistor between ACP and ACN plus the OVPSET divider and the internal loop. The part throttles the PWM when the input current reaches the limit, so a 12 V 1 A adapter can charge a three cell pack at about 10 W without collapsing.

Does the part need a thermistor? It has a TS input, and the JEITA behaviour depends on the member and on the external network. A build without a thermistor has to tie the pin to a voltage inside the window, and the value has to match the network the document shows rather than a resistor copied from another charger.

Is a second sense resistor needed for the pack current? The charge current is sensed in the path between the inductor and the pack, and the input current is sensed across ACP and ACN. A system that needs a separate pack current reading has to add its own sense element, because neither of these is brought out as an analog output.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.