BQ24103RHLR
Product Specifications
BQ24103RHLR
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ24103RHLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ24103RHLR: the 4.2 V stand-alone member of the bqSWITCHER charger family
BQ24103RHLR is the 4.2 V single-cell assembly of the bq241xx synchronous switch-mode charger family, the part that carries the integrated power FETs, the 1.1 MHz fixed-frequency PWM controller and the full charge state machine in one 20-pin VQFN body. It is the stand-alone version: the device runs its own conditioning, constant current and constant voltage sequence without a host processor writing registers, and reports what it is doing on two status pins.
The string in the catalogue is the plain bq24103 with the RHL carrier and the R suffix for a 3000 piece reel. That matters because the family has an A revision, bq24103A, which adds a CELLS pin so the same body can charge a one-cell or a two-cell pack at 4.2 V or 8.4 V. A build that has already fixed a single-cell pack does not need that pin, and the plain string is the one that appears on the vendor addendum for this reel quantity.
What follows is what SLUS606P fixes for the device: the voltage and current thresholds that decide the circuit around it, the two programming resistors that set fast charge and termination, the temperature window the TS pin enforces, and the carrier rows the addendum actually prints for this suffix.
What the order code sits on
| Function | synchronous switch-mode Li-Ion and Li-Polymer charger with integrated FETs |
| Cell count | one cell, 4.2 V regulation, the 03A revision adds a CELLS pin for two cells |
| Package | VQFN, 20 pins, 3.50 mm by 4.50 mm |
| Switching frequency | 1.1 MHz fixed, 0 to 100 percent duty cycle |
| Charge current range | up to 2000 mA, set by the resistor on ISET1 |
| Input and output rating | 20 V maximum on the IN and OUT pins |
| Voltage regulation accuracy | 0.5 percent at 25 degrees, 1 percent over the full window |
| Precharge threshold | 68 to 75 percent of the regulation voltage, 71.4 percent typical |
| Precharge current | 15 to 200 mA, set by the resistor on ISET2 |
| Termination current range | 15 to 200 mA, 100 mV set voltage on ISET2 |
| Recharge threshold | 75 to 125 mV per cell below regulation, 100 mV typical |
| Sleep current | 5.5 microamps maximum at 4.2 V cell voltage |
| Temperature window | cold 72.8 to 74.2 percent, hot 33.7 to 35.1 percent, cutoff 28.7 to 29.9 percent of the TS bias |
| Battery detection | built in, with a 40 ms deglitch on the termination comparator |
| Status pins | STAT1 and STAT2, charge in progress, complete, fault and adapter present |
The three phases and the thresholds between them
The device charges in conditioning, constant current and constant voltage, and the borders between them are fixed by the data sheet rather than by an external resistor. Conditioning ends when the cell reaches the VLOWV window, printed as 68 percent minimum, 71.4 percent typical and 75 percent maximum of the regulation voltage, with a 20 to 40 ms deglitch on the rising edge. On a 4.2 V cell that is a transition somewhere between 2.86 V and 3.15 V, so a deeply discharged pack spends its first minutes in precharge at a current set by the ISET2 resistor and nothing else.
That spread is the reason a fuel gauge calibrated on one board can read differently on the next. The transition is not a single voltage; it is a window of nearly 300 mV on a single cell, and the pack voltage crosses it while the charger is pushing current into the cell, so the apparent state of charge at the handover moves with the charge rate and with cell impedance. A test that records the transition point at one temperature cannot be used as a limit at another.
Constant current ends when the cell reaches the regulation voltage, and the device then holds 4.2 V until the current tapers to the termination threshold. The termination comparator looks at the voltage across the sense resistor, compares it with a 100 mV reference, and trips at 20 percent accuracy, which is wide. The practical consequence is that a pack built with two different sense resistors, or with a resistor of a different tolerance, can terminate at currents that differ by tens of milliamps, and the reported capacity of a full charge moves with it.
After termination the device waits for the cell to fall by the recharge threshold before it starts again. That threshold is 75 mV minimum, 100 mV typical and 125 mV maximum per cell, so on a 4.2 V pack a restart happens somewhere between 4.075 V and 4.125 V. A system that polls the status pins and assumes the charger is off after a full charge will see it switch back on during a long idle period, which is normal behaviour and not a fault.
Setting current with two resistors
Fast charge current is set by the resistor from ISET1 to ground. The data sheet gives the set factor as 1000 volts per amp and the regulated voltage across the sense resistor as 1 V at the ISET1 pin, so a 10 k resistor with a 10 milliohm sense resistor gives 1 A, and a 5 k resistor gives 2 A, which is the top of the range. The accuracy of that regulated voltage is plus or minus 10 percent before the tolerances of the two resistors are counted, and the data sheet says so explicitly rather than folding those terms into the headline.
Termination shares the ISET2 pin with precharge, which is why the two currents are not free of each other. The termination set voltage is 100 mV against a 1000 volts per amp factor, so the same resistor that programs 200 mA of precharge programs a different threshold in the taper comparator. A build that changes ISET2 to speed up conditioning also moves the current at which the charger declares the pack full, and the charge time moves with it.
The sense resistor itself is the part of the loop that most often disagrees with the drawing on paper. The regulation loop controls the voltage across it, so its tolerance and its temperature coefficient appear directly in the charge current, and a 1 percent part with 100 ppm drift over a 40 degree rise adds a term that is larger than some of the amplifier errors. A four-terminal connection to the sense resistor is the usual answer, and the copper between the resistor and the SNS and BAT pins belongs to the measurement path.
Temperature sensing and the TS window
The TS pin expects a thermistor biased from the VTSB output and compares the divider against three internal thresholds. Cold is 72.8 to 74.2 percent of the bias, hot is 33.7 to 35.1 percent and cutoff is 28.7 to 29.9 percent, so the same 10 k NTC with a 103AT curve gives a charge window that is fixed by the divider rather than configurable in software. A pack that must charge above 45 degrees needs a different divider, and a pack that must not charge at all below zero needs the cold threshold moved, both of which are resistor changes on the pack board.
The hot and cold windows are what a medical or industrial customer usually asks about first, because the charger is often the only part of the system that decides whether a battery is allowed to take energy at all. The thresholds above are ratios of the bias voltage, not absolute resistances, so they track the bias regulator and stay put across temperature as long as the thermistor curve is the one the divider was calculated for.
Thermal behaviour in a 3.5 mm by 4.5 mm body
The integrated FETs are the reason the body is small and the reason the board copper matters. At 2 A into a 3.7 V cell from a 5 V adapter the converter is dissipating a few tenths of a watt, which the 20-pin VQFN can pass into a modest copper area. At 2 A into a 4.2 V cell from a 12 V input the same current is dropped across a much larger differential, the dissipation climbs into the region where the thermal regulation loop starts to fold the current back, and the charge time extends instead of the die overheating.
Thermal regulation is a feature and not a fault, but it changes what a production test sees. A board tested on a bench at 25 degrees with free air will complete a charge cycle in the calculated time, while the same board inside a sealed enclosure will take longer and will show a current that steps down partway through the cycle. The 85 degree operating limit on this reel row is an ambient figure, so the enclosure temperature is the number to check, not the bench temperature.
Carriers, reels and what the addendum prints
| BQ24103RHLR | VQFN RHL, 20 pins, 3000 pieces on a large reel, active |
| BQ24103RHLR.B | same body and reel, the .B row of the same string |
| Lead finish | NIPDAU, nickel palladium gold |
| Moisture level | Level-2-260C-1 YEAR, one year floor life after the seal is broken |
| Operating temperature | minus 40 to plus 85 degrees ambient on the addendum row |
| Part marking | CID on the plain RHLR row |
| RoHS | Yes on the reel rows |
| Small reel option | the 250 piece T row exists on the A revision, marking CKO |
| Two-cell revision | bq24103A, same 20-pin body, CELLS pin added |
The reel quantity is the first thing to confirm when a purchase order is written, because the plain string is published at 3000 pieces and a prototype build usually wants a few dozen parts. The 250 piece T row on this family belongs to the A revision, so a buyer who needs a small reel of the plain bq24103 is asking for a partial reel rather than for a published carrier, and the distributor has to say which it is shipping.
Moisture level 2 with a one year floor life is the other line worth reading. A board house that keeps reels on the shelf for longer than that has to bake before reflow, and a charger that has absorbed moisture can fail at the reflow profile in a way that looks like a silicon fault on the test bench. Our assembly lines store this class of part in dry cabinets and record the seal date on the reel label, which is the record a customer audit asks for.
Where this charger still fits in a new build
Stand-alone chargers remain the right choice for products that must work out of the box, with no host code to bring the charger up, and for products where the battery is a service item rather than a managed subsystem. A handheld instrument, a portable media player or an industrial handheld with a single cell and a 5 V adapter is the case this part was written for, and the two status pins are enough for an LED or a single GPIO.
The family is also the natural second source when a newer charger has a long lead time, because the pinout is fixed by the 20-pin RHL body and the external parts are a sense resistor, an inductor and a handful of capacitors. When a customer sends a BOM with a charger they can no longer buy, the cross reference work starts from the cell count, the charge current and the status pin logic rather than from the part number. If a substitute has to be checked against an existing board, the workflow on our power management cross reference page lists what to compare before a sample is ordered, and the obsolete part cross reference hub covers the case where the original string is no longer produced at all.
Questions buyers ask before a first order
Does this part charge two cells? Not on this string. The plain bq24103 regulates 4.2 V and has no CELLS pin; the 03A revision in the same body is the one that switches between 4.2 V and 8.4 V. Ordering the plain part for a two-cell pack produces a charger that stops at half the pack voltage and never terminates.
Can the charge current be changed without a board change? Yes, by changing the ISET1 resistor, up to the 2 A ceiling of the integrated FETs. Above that the part is out of range regardless of the resistor, and a board that needs 3 A has to move to a controller with external FETs.
What happens if the battery is removed during a charge? The device has built-in battery detection and drives its status pins in a pattern that indicates the absence of a pack, so a system that reads both pins can tell a missing battery from a finished charge.
Which document version applies? SLUS606P, revised November 2015, is the current revision of the family document and the one the numbers above come from. A customer holding an older copy will find different resistor values in the application examples, because several of them were corrected in later revisions.