TPS62153RGTR
Product Specifications
TPS62153RGTR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS62153RGTR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS62153RGTR: a 17 V, 1 A step-down converter with a fixed 5 V output
TPS62153RGTR is a 3 V to 17 V synchronous step-down converter in a VQFN (RGT) body of 16 pins. The RGT body is the 3 mm by 3 mm 16 pin QFN, and the 53 in the ordering string is the fixed 5.0 V member of the TPS6215x family. The reel is 250 pieces rather than the 3000 of the larger bodies, which is worth knowing before a production schedule is planned around it.
Order code and package
| TPS62153RGTR | VQFN (RGT), 16 pins, 3 mm by 3 mm, 250 piece reel, fixed 5.0 V output |
| TPS62153RGTT | same body, the small reel ordering string used for samples |
| TPS62150 | adjustable member of the same family, 0.9 V to 6 V |
| TPS62151 and TPS62152 | fixed 1.8 V and 3.3 V members, same pins and same body |
| Power good logic | high impedance when EN is low on this family member, which decides the pull up value on the PG pin |
Electrical parameters that decide the application
| Input and output | 3 V to 17 V in, 5.0 V fixed out on this ordering string, 20 V absolute maximum on AVIN and PVIN |
| Current | up to 1 A continuous, with the output held in 100 percent duty cycle mode when the input falls towards the output |
| Switching frequency | 2.5 MHz typical, which is what allows a small inductor and a fast transient response |
| Topology | DCS-Control, a hysteretic and voltage mode combination that keeps accuracy across the load range |
| Quiescent current | 17 uA typical with EN high and no load, 2 uA maximum in shutdown |
| Soft start | programmable through the SS/TR pin, which also allows tracking against another rail |
| Frequency option | selectable operating frequency through the FSW pin |
| Protection | short circuit protection and overtemperature protection, with the power good output reporting the state to the controller |
| Compatibility | pin to pin with the TPS62130 and the TPS62140 families |
| Mounting | 3 mm by 3 mm VQFN with an exposed pad, so the thermal path runs through the vias under the part |
Family variants and how they differ
| TPS62150 | adjustable 0.9 V to 6 V through an external divider, same body and pins |
| TPS62151 | fixed 1.8 V, the same converter with the divider inside |
| TPS62152 | fixed 3.3 V, the member most often quoted against this 5.0 V version |
| TPS62150A | the variant whose power good output goes low when EN is low, against the high impedance of the other members |
| TPS82150 module | the same converter with the inductor integrated, for a board that cannot place a discrete inductor next to the part |
Points to check before this part goes on a BOM
The fixed 5.0 V output is set inside the part, so there is no divider to get wrong and no feedback trace to keep short. The trade is that a 5 V rail is the only thing this ordering string produces: a 3.3 V rail needs TPS62152RGTR and a 1.8 V rail needs TPS62151RGTR, both on the same pads. A BOM that lists the family name without the suffix produces boards at the wrong voltage with no visible difference on the assembly.
The 2.5 MHz switching frequency is what makes the 3 mm by 3 mm body practical. At that frequency the inductor is small enough to sit beside the part on a dense board, and the transient response is fast enough for a load that steps between milliamps and an amp. The cost is switching loss, which is why the part is efficient at light load through power save mode rather than by running continuously.
Power good polarity is a detail that catches second sources. On this family member the PG pin is high impedance when EN is low, while the TPS62150A drives it low in the same state. A controller that reads PG as a reset signal behaves differently against the two parts, so the pull up and the logic sense have to be checked when a substitute is offered.
The 250 piece reel is the practical constraint on a production plan. It is the standard carrier for this body, so a schedule that assumes 3000 piece reels will need either a different ordering string or a consolidation step. That is worth confirming at quote stage rather than when the line is waiting.
Where a fixed 5 V buck is the right answer
A 12 V intermediate rail that has to produce 5 V for a housekeeping supply does not need an adjustable converter. The fixed member removes the divider, removes the tolerance stack of two resistors, and removes the feedback trace that has to stay away from the switch node. On a board with several rails the simplicity is worth more than the flexibility.
The 3 V to 17 V window covers a 12 V rail plus its tolerance and a lithium battery directly, and the 100 percent duty cycle mode holds the output up when the input sags towards 5 V. A rail that has to survive a 12 V bus dip therefore keeps regulating longer than a converter that stops switching at the dropout point.
The family is also one of the few where a pin compatible ladder covers the common logic rails: TPS62150 adjustable, TPS62151 at 1.8 V, TPS62152 at 3.3 V and this TPS62153 at 5.0 V, all in the same 16 pin body with the same external components. A board that may be reused across three products can keep one footprint and change one ordering string, which shortens both the qualification and the incoming inspection. The catch is that nothing on the assembled board shows which one was fitted, so the test step has to measure the output rather than trust the BOM, and a second source offered against any member of the ladder has to be checked the same way, with the output measured at the connector rather than at the converter, since a fixed voltage member gives no clue on the board itself, and the test step is where the difference is caught before the board ships.
Where this order code fits
It supplies 5 V housekeeping and logic rails from a 12 V bus, solid state drives, embedded systems and set top boxes that need a small, quiet 1 A converter. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
How do I get 3.3 V from the same family? With TPS62152RGTR, which is the fixed 3.3 V member on the same 16 pin body. The 53 suffix on this page is 5.0 V only, and the voltage is set inside the part.
Why only 250 pieces on the reel? That is the standard carrier for this body and ordering string. Production quantities arrive as multiple reels rather than a single 3000 piece one, so a schedule has to count reels rather than assume the larger carrier.
What is the input range with margin? 3 V to 17 V operating, 20 V absolute maximum on AVIN and PVIN. The 100 percent duty cycle mode keeps the output in regulation as the input approaches 5 V, which is what makes it usable on a 12 V bus that dips.
Does the power good pin need a pull up? It is high impedance when EN is low on this member, so it needs a pull up to the local logic rail. That behaviour differs on the TPS62150A, which drives the pin low in the same state, so the pull up and the logic sense are checked when substituting.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.