Contact Us

ADG1606BCPZ-REEL7

Brand: Analog Devices
Analog Devices ADG1606BCPZ-REEL7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADG1606BCPZ-REEL7 — Analog & Mixed-Signal ICs | Superb Automation

ADG1606BCPZ-REEL7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADG1606BCPZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

ADG1606BCPZ-REEL7: 16 inputs to one output, and the 378 mA figure that needs a thermal check first

The ADG1606BCPZ-REEL7 is a 16 channel single ended analog multiplexer built on the iCMOS process, with a 4 bit binary address (A0 to A3) and an enable pin that turns every channel off when it is asserted. The BCPZ in the order code is the 32 lead 5 mm by 5 mm LFCSP body, not the 28 lead TSSOP, so a buyer comparing two quotations with the same base part number has to read the suffix before comparing the price. The part conducts in both directions, the signal range runs to both supplies, and no VL logic rail is needed because the digital inputs are specified at 2.0 V high and 0.8 V low.

Four and a half ohms typical sounds like a small number until the switch is asked to carry current rather than a voltage. The same part is specified at 7.5 ohms maximum over temperature, a rise of 66.7 percent on the typical figure, and the on resistance flatness of 1.1 ohms is 24.4 percent of the typical value. Both numbers decide whether the multiplexer can sit in a signal path without being the largest distortion term in it.

What the vendor page states

ParameterValue
Configuration16 single ended channels to one common output, 4 bit address, EN pin
On resistance4.5 ohm typical, 7.5 ohm maximum over temperature
On resistance flatness1.1 ohm
Suppliesplus or minus 3.3 V to plus or minus 8 V dual, 3.3 V to 16 V single
Signal rangerail to rail, extends to both supplies
Logic inputs3 V compatible, VINH 2.0 V, VINL 0.8 V, no VL supply needed
Continuous current per channelup to 378 mA
DistortionTHD plus N 0.04 percent
Bodies28 lead TSSOP, 32 lead 5 mm by 5 mm LFCSP
SiblingADG1607, the same switch as 8 differential channels on a 3 bit address

What 378 mA costs inside the switch

The current rating is the switch and package limit, not a target. At 100 mA the typical 4.5 ohms drops 0.45 V and burns 45 mW, and the worst case 7.5 ohms drops 0.75 V and burns 75 mW. At 200 mA the worst case is 1.5 V and 300 mW. At the full 378 mA the worst case drop is 2.835 V and the dissipation inside one channel is 1.07 W, which no 5 mm by 5 mm body will hold without a copper area under it. A relay replacement that carries 200 mA through this part is really a thermal question, and the LFCSP body is the one to quote when the current is above a few tens of milliamps.

Driving the address from a 3.3 V host

The 2.0 V threshold is 60.6 percent of a 3.3 V rail and the 0.8 V low threshold is 24.2 percent, so a 3.3 V microcontroller drives the four address lines and the enable directly with no level shifting and no second supply. This is the practical difference from older multiplexers that needed a separate logic rail: fewer pins to route, one less rail to sequence at power up. What the page does not publish is the state of the switch during the first milliseconds after the supplies come up, so a system where a channel must not conduct before the controller is awake has to hold EN at a defined level from a pull resistor rather than rely on a reset default.

Where the part sits in a data acquisition chain

Sixteen channels on one output is a 16 to 1 reduction in the number of amplifiers behind the switch, and the price is that the amplifier sees a source resistance that changes with the selected channel. With 4.5 ohms typical and a settling requirement inside one conversion window, the series resistance and the sample capacitor form the time constant that sets the acquisition time, which is why the maximum on resistance at the operating temperature, not the typical figure at 25 C, is the number to request from the supplier. Related multiplexers and switches are indexed on the Analog and mixed-signal ICs page, and the sourcing routes for a line that mixes these parts with other suppliers are collected under pin to pin cross reference and BOM shortage recovery.

ADG1606BCPZ-REEL7: sixteen channels with one flatness number between them

A 4.5 ohm typical on resistance with 1.1 ohm of flatness across the signal range is a statement about one channel, and a 16 to 1 multiplexer puts sixteen of those channels in front of a single converter. The channel to channel variation is what a multiplexed measurement actually sees: if two channels differ by a quarter of the typical resistance, into a 10 kohm load that is 0.011 percent of gain difference, which is a systematic offset between channels that a calibration has to remove. The address is a 4-bit binary code on A0 to A3, and the enable pin turns all sixteen off.

ItemPublished valueArithmetic or consequence
Configuration16 single channels to one outputFour address lines, so the scan is 16 steps
On resistance4.5 ohm typical0.045 percent of gain error into 10 kohm
Flatness1.1 ohm24 percent of the typical value, the distortion term
CurrentUp to 378 mA per channel0.64 W at 4.5 ohm, which is the thermal question
SupplyPlus or minus 3.3 V to plus or minus 8 V, 3.3 V to 16 V singleA 24 V industrial rail is outside the family
Logic3 V compatible, no separate logic supplyThe host can drive the address directly from 3.3 V
Body28-lead TSSOP, 32-lead 5 mm LFCSPSixteen channels in a 5 mm square needs the exposed pad

Settling through the multiplexer is a two part budget

Switching from one channel to the next connects a new source to the converter input through 4.5 ohm plus the channel capacitance, and the settling time is set by that resistance times the total capacitance at the node, including the converter sample capacitor. A 100 pF node and 4.5 ohm give a time constant of 0.45 ns, so the multiplexer is rarely the limit and the drive amplifier usually is. That is worth stating because the 16 channel scan rate is often blamed on the switch when the buffer is the slower element.

Off isolation and leakage decide the channel that is not selected

In a 16 channel system the interesting failure is the unselected channel leaking into the measured one, and that is a data sheet specification rather than a headline feature. The enable pin is the second half of the answer, because a controller that scans by changing the address alone leaves the unselected path connected to the bus and the leakage sums. On a high impedance source, twenty nanoamps of leakage through 100 kohm is 2 mV, which is visible at 16 bits.

Buying this order code

The BCPZ suffix is the LFCSP body and it has to match the pad on the board, since the TSSOP body is a different footprint in the same family. The multiplexer family is on the analog line card, the 8 channel differential version is compared on the pin to pin page, and the 28-lead body is quoted through the lead time desk.

Request Quote — In Stock, 100% New & Original, Full Warranty