AD8627ARZ-REEL7
Product Specifications
AD8627ARZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8627ARZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD8627ARZ-REEL7: 1 pA of bias, 500 microvolts of offset, and 750 microamps to get there
The AD8627ARZ-REEL7 is a single JFET input operational amplifier with rail to rail output, a maximum input bias current of 1 pA, a maximum offset of 500 microvolts, a supply current of 750 microamps per amplifier and a supply range from 5 V to 26 V single or plus or minus 2.5 V to plus or minus 13 V dual. It is unity gain stable and specified to survive input overdrive without phase reversal. The ARZ body is the 8 lead SOIC; the same die is offered in a 5 lead SC70, and the family includes the AD8626 dual and the AD8625 quad.
This is the part chosen when a sensor has an output impedance in the gigohm range and the amplifier has to sit on a 12 V or 15 V rail: photodiode front ends, pH and ion selective probes, electrometer stages, high impedance bridge buffers. The bias current is what gets it shortlisted, and the offset is what usually decides the resolution of the stage.
What the vendor page states
| Parameter | Value |
|---|---|
| Channels | One, JFET input, rail to rail output |
| Input bias current | 1 pA maximum |
| Offset voltage | 500 microvolts maximum |
| Supply current | 750 microamps per amplifier |
| Supply range | 5 V to 26 V single, plus or minus 2.5 V to plus or minus 13 V dual |
| Stability | Unity gain stable |
| Overdrive | No phase reversal |
| Family | AD8625 quad, AD8626 dual, AD8627 single |
| Bodies | 5 lead SC70 and 8 lead SOIC |
Where the error actually comes from
At 1 pA the bias current produces 1 microvolt across a 1 Mohm source, 10 microvolts across 10 Mohm and 1 mV across 1 Gohm. The 500 microvolt offset is 50 times the bias error at 10 Mohm, so on any source below about 500 Mohm the offset dominates and the bias specification is not what limits the measurement. That ordering matters when a substitution is considered: a part with ten times the bias current would still contribute only 100 microvolts at 10 Mohm and would be invisible next to a 500 microvolt offset, while a part with a better bias figure and a worse offset would make the stage worse.
The supply budget is the other side of a JFET input. Seven hundred and fifty microamps at 26 V is 19.5 mW, and at 5 V it is 3.75 mW, a factor of 5.2 between the two ends of the same specification. A 15 V rail front end therefore has to account for a part that burns five times the power of the same part on 5 V, which is normal for a JFET input stage and is the reason CMOS parts with 1 pA bias exist alongside it for low voltage work. The 26 V ceiling is unusually high for an amplifier in an 8 lead body and is the property that makes the part useful in industrial front ends that run straight off a 24 V rail with a small series resistor.
Questions buyers ask before ordering
Does the 1 pA hold at 125 degrees C? The 1 pA figure is a maximum for the part at the specified condition, and JFET gate leakage rises steeply with temperature. The data sheet carries the curve, and any high temperature claim has to come from it rather than from the room temperature line.
Is the 5 lead SC70 the same part as the 8 lead SOIC? Electrically the same die; the body decides the thermal resistance and the assembly process. A reel ordered as ARZ is the SOIC, which is what a rework station and an 8 lead footprint expect.
Can it be used as a transimpedance amplifier for a photodiode? Yes, that is one of its main uses: 1 pA of bias current and a rail to rail output on a 15 V rail suits a reverse biased photodiode with a feedback resistor in the tens of megohms. The feedback resistor sets the bandwidth, and the 1 pA bias then sets the floor of the stage.
How this part is supplied
This reel is part of the Analog Devices analog and mixed signal range kept for production, and JFET input amplifiers are grouped in the amplifier cross reference by bias current, supply ceiling and body. For a running line where the body has to stay the same, the lead time options page sets out how the single, dual and quad members of the family are quoted against one another and what has to be rechecked when the count changes.
Request Quote — In Stock, 100% New & Original, Full Warranty