ADR3433ARJZ-R7
Product Specifications
ADR3433ARJZ-R7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADR3433ARJZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADR3433ARJZ-R7: 0.1 percent initial accuracy becomes 0.23 percent over temperature
The ADR3433ARJZ-R7 is a 3.3 V voltage reference in a 6 lead SOT-23, trimmed at final assembly to plus or minus 0.1 percent and specified at 8 ppm per degree C maximum drift across the industrial range. It sources up to 10 mA and sinks 3 mA, draws 100 microamps maximum, and drops out at 250 mV at a 2 mA load. The ARJZ body is the SOT-23-6, and it belongs to the ADR34xx family where the last two digits carry the output voltage, so the ADR3430 next to it in a bill of materials is a 3.0 V part and not a substitute.
Two numbers on this page decide whether the part can be used: the initial accuracy and the drift. They are usually read separately and added in a rough way, and the arithmetic below shows why the second one dominates.
What the vendor page states
| Parameter | Value |
|---|---|
| Output | 3.3 V |
| Initial accuracy | plus or minus 0.1 percent |
| Temperature coefficient | 8 ppm per degree C maximum |
| Quiescent current | 100 microamps maximum |
| Output current | 10 mA source, 3 mA sink |
| Dropout | 250 mV at 2 mA |
| Output noise | below 10 microvolts peak to peak, 0.1 Hz to 10 Hz |
| Temperature range | minus 40 to plus 125 degrees C |
| Body | 6 lead SOT-23 |
| Family | ADR3412, 3420, 3425, 3430, 3433, 3440, 3450, same die different trim |
Adding the two error terms
Plus or minus 0.1 percent of 3.3 V is 3.3 mV. Eight ppm per degree C across 165 degrees is 1,320 ppm, which is 4.36 mV. The worst case window is the sum, 7.66 mV, or 0.232 percent of the output. The drift term is larger than the initial accuracy term, so a buyer who asks only for a tightly trimmed part has asked for the smaller half of the error.
Put against converter resolution, 7.66 mV is 9.5 codes of a 12 bit converter referred to 3.3 V, where one code is 805.7 microvolts, and 152 codes of a 16 bit converter, where one code is 50.35 microvolts. That is the figure to put in a resolution budget: a 16 bit measurement cannot be better than roughly 7 bits of absolute accuracy if this reference is the only one in the chain, unless it is calibrated at the temperature it runs at.
The noise is a different matter. Below 10 microvolts peak to peak from 0.1 Hz to 10 Hz is 1.2 percent of a 12 bit code at 3.3 V, so the reference contributes almost nothing to short term noise and everything to long term drift. Quiescent current is 0.33 mW at 3.3 V.
Questions buyers ask before ordering
Can the ADR3433 run from a 3.3 V rail? No. The dropout is 250 mV at 2 mA, so the input needs 3.55 V before the output can hold 3.3 V. A 3.3 V rail feeding a 3.3 V reference is the most common mistake with this family, and it shows up as a reference that tracks its own supply instead of regulating.
Is the ADR3430 an alternative? Only if the system wants 3.0 V. The family shares a die and a package and differs in output voltage, so the substitution changes full scale and every code size derived from it.
How much current can it deliver continuously? 10 mA source and 3 mA sink. Beyond that the output is no longer specified, and a reference used to drive a bridge directly will sit outside its own error budget.
How this part is supplied
The ADR3433 is held inside the Analog Devices analog and mixed signal range, and references are listed by output voltage and drift grade in the power management cross reference. Where a build needs a different voltage from the same family, that page is the fastest route to a part that keeps the footprint, and for a line that has run out mid build the BOM shortage recovery route covers the rest of the board at the same time.
Request Quote — In Stock, 100% New & Original, Full Warranty