Contact Us

TPS61240YFFR

Brand: Texas Instruments
Texas Instruments TPS61240YFFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS61240YFFR — Power Management & Signal Chain | Superb Automation

TPS61240YFFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS61240YFFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS61240YFFR: 3.5 MHz step up converter, fixed 5.0 V, 450 mA, in a 6 pin chip scale body

TPS61240YFFR is a fixed 5.0 V synchronous boost converter that lifts a single cell or a three cell alkaline pack to a regulated 5 V rail without an external Schottky diode in a DSBGA body of 6 pins. It takes 2.3 V to 5.5 V in, delivers a regulated 5.0 V at up to 450 mA, switches at 3.5 MHz so the inductor can be a 1 uH chip part, and draws 30 uA typical with the output at no load. The YFF body is a 6 ball chip scale package with 133 C per watt junction to ambient, which is the figure that limits how much of the 450 mA a small board can actually use.

Order code and package

TPS61240YFFR6 ball DSBGA (YFF), 3000 pieces on a large reel, tin silver copper balls, moisture level 1 unlimited
TPS61240YFFTsame body, 250 pieces on a small reel, the prototype quantity
TPS61240DRVR6 pin WSON (DRV), 3000 pieces on a large reel, 104.1 C per watt, the body to choose when the board can give up 2 mm by 2 mm
TPS61241YFFRsame family, lower switch current limit, 250 pieces on a small reel
Operating temperatureminus 40 C to plus 125 C junction, all rows in the addendum carry the same grade

Electrical parameters that decide the application

Input voltage2.3 V to 5.5 V operating, with the output already regulated before the input reaches its lockout
Output voltage5.0 V fixed, plus or minus 2 per cent total DC accuracy at nominal conditions
Output currentup to 450 mA, limited by the input valley current limit rather than by a thermal promise
Switch valley current limit500 mA on the TPS61240, 200 to 350 mA on the TPS61241 and TPS61242
Switching frequency3.5 MHz typical, fixed, no resistor to set it
Quiescent current30 uA typical and 40 uA maximum with the enable pin high and no load
Shutdown current1.5 uA with the enable pin at ground
Undervoltage lockout2.1 V rising and 2.0 V falling, with the part starting to switch only after the rising trip
Output ripple20 mV peak to peak from 2.3 V to 5.5 V in over 0 to 200 mA out
Thermal shutdown140 C junction with 20 C of hysteresis, non latching

How the three family members differ

TPS61240500 mA valley current limit, the member in this page, and the only one that reaches the 450 mA output claim
TPS61241200 to 350 mA switch valley limit, for a load that does not need the full current and a smaller inductor
TPS61242same lower limit with the output set for a different rail in the family table
Soft startinternal, 300 us ramp from 5 per cent to nominal, with the switch limit cut to 300 mA until the output passes the input
Body optionsDSBGA at 133 C per watt against WSON at 104.1 C per watt, same die and same pinout
No external diodesynchronous rectification is inside, so the only power components left are the inductor and two capacitors

Points to check before this part goes on a BOM

The 450 mA headline is an output current at a stated input, not a promise at the bottom of the input range. A boost converter draws more input current than it delivers, so at 2.3 V in and 5 V out the input side is already near 1 A for 450 mA of load, and the 500 mA valley limit sits on the switch current rather than on the output. A program that needs 450 mA at 3.6 V in is comfortable, one that needs it at 2.5 V in is not, and the efficiency curve in the document shows the crossover.

The 3.5 MHz switching frequency is what makes a 1 uH inductor enough. It also pushes the switching loss up, which is why the efficiency holds above 90 per cent at nominal load and falls away at light load. A customer comparing this part with a 1.2 MHz boost of the same current rating is trading inductor size against efficiency, and on a 5 V rail at 200 mA the difference shows up as a few tens of milliwatts.

The soft start row is the one that decides whether a board survives a heavy output capacitor. The part limits the switch current to 300 mA until the output voltage passes the input voltage, and only then allows the full 500 mA valley limit. With a 22 uF output capacitor, that pre-charge phase is what keeps the input rail from collapsing when the converter starts into a discharged load, and with a much larger capacitor the start time simply stretches out.

The undervoltage lockout sits at 2.1 V rising and 2.0 V falling, and the 2.3 V bottom of the operating range is above both. That ordering matters for a single cell alkaline pack, where two fresh cells are 3.2 V and two tired cells are 2.0 V. The converter will run from two tired cells at no load and drop out under load, which is the behaviour a battery life test will show as a cliff rather than a slope.

The chip scale body is the thermal limit, not the silicon. At 133 C per watt, 300 mW of loss raises the junction 40 C above the board, and 450 mA at 5 V from 3.6 V in is around 90 per cent efficient, so the loss is roughly 250 mW. On a 4 layer board with a ground plane under the part that is fine at 25 C ambient and marginal at 70 C, which is why the same die also ships in a WSON body at 104.1 C per watt.

The 20 mV peak to peak output ripple figure is quoted from 2.3 V to 5.5 V in over 0 to 200 mA, which is a narrow slice of the load range. Above 200 mA the ripple grows with the load step and with the output capacitor ESR, and a 10 uF ceramic is the value the vendor curves assume. A 4.7 uF capacitor will show visibly more ripple at the same load, and the fix is capacitance rather than a different part.

The shutdown current of 1.5 uA is what a battery product budgets when the rail is off, but the enable pin is the only thing that gets the part there. On an always on 5 V rail powered from a lithium cell, the 30 uA quiescent current is the number that matters, and it is high enough that a product sitting idle for weeks has to consider a load switch ahead of the converter rather than leaving it enabled.

Where this order code fits

It powers 5 V loads from a single lithium cell or a three cell alkaline pack: portable instruments, wireless sensors, USB accessories running from a battery, and any handheld product where a 5 V rail has to come out of a 3 V to 4.2 V cell. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

How much current can it really deliver at 5 V? 450 mA is the figure at a healthy input. From 3.6 V in the part holds it, from 2.5 V in the input current needed already approaches the switch limit, so the usable output falls. Read the load against the input voltage on the efficiency curve rather than the headline.

Does it need an external Schottky diode? No. The rectifier is inside the part. The external components are the inductor, an input capacitor and an output capacitor, which is why the body can be 6 balls.

What happens when the battery falls below 2.1 V? The undervoltage lockout stops switching at about 2.0 V falling and the output follows the input through the inductor and body diode path, so the rail is no longer regulated. It restarts at 2.1 V rising.

Is the 5.0 V output trimable? No, it is fixed at 5.0 V plus or minus 2 per cent. The adjustable member of the family is a different order code, and this body has no feedback pin to change it.

Which body should be used on a dense board? The chip scale body saves area, the WSON body runs 29 C per watt cooler. At loads near the 450 mA figure the WSON is the safer choice unless the board has a solid ground plane under the part.

Can two of these be paralleled for more current? Not directly. Two boost converters do not share current without a droop mechanism, and the valley current limit of each will fight the other. A single converter with a higher switch rating is the route.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.