Contact Us

TPS7A0530PDBVR

Brand: Texas Instruments
Texas Instruments TPS7A0530PDBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A0530PDBVR — Power Management & Signal Chain | Superb Automation

TPS7A0530PDBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A0530PDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A0530PDBVR: a 3.0 V, 200 mA regulator with a 1 uA quiescent current

The TPS7A0530PDBVR is the 3.0 V fixed output of the TPS7A05 family, a 200 mA linear regulator specified at 1 uA of quiescent current typical and 3 uA maximum. It takes 1.4 V to 5.5 V at the input, covers 0.8 V to 3.3 V at the output in fixed steps, and ships in the five pin SOT-23 coded DBV with 3000 pieces on a large reel. Compared with the nanopower TPS7A03 line, this part trades a fraction of a microamp of standby current for a tighter current limit and an active output discharge.

The discharge circuit matters more than it sounds. When the enable pin goes low, an internal resistor pulls the output to ground instead of letting the rail decay through the load, which guarantees a known state for a microcontroller that is being power cycled and prevents a reverse bias across an analog front end. The family also uses foldback current limiting, so the current available during a short is far below the rated 200 mA.

Key electrical data for the 3.0 V point

Input range1.4 V to 5.5 V, 3.5 V minimum for full regulation at 200 mA
Output current200 mA, current limit 210 mA to 700 mA, short circuit 65 mA to 150 mA
Quiescent current1 uA typical, 3 uA maximum, ground current 6 uA at full load
Shutdown current100 nA typical, 300 nA maximum
Accuracy1 percent typical, 3 percent maximum over temperature
Dropout at 200 mA235 mV maximum at 3.3 V output, 212 mV typical in the 1.8 V to 2.5 V band
Stability0.47 uF or larger ceramic on the output, 1 uF on the input where the source is inductive

Package, marking and reel data

BodySOT-23 DBV, 5 pins, 2.9 mm by 1.6 mm
Reel3000 pieces, large tape and reel, 180 mm carrier, 8 mm tape
FinishSN on the plain row, NIPDAU on the G4 row of the same code
Moisturelevel 1, 260 C peak reflow, unlimited floor life
Marking1QWF

Where a 3.0 V, 1 uA rail belongs

The obvious home is an always on domain in a battery product: a real time clock, a wake circuit, a thermostat, a smoke or heat detector, a gas or water meter, an electronic shelf label or a portable medical monitor. In those products the regulator is enabled for years and the load is a few microamps, so the quiescent current is the dominant term in the battery budget and 1 uA is already a hundred times the load.

The second use is a keep alive rail that has to be clean as well as cheap. The family keeps its ground current low in dropout, which means a product that runs from a 3.6 V lithium cell keeps drawing microamps as the cell falls to 3.0 V instead of climbing to tens of microamps the way an adaptive bias regulator does. The cost of that behaviour is a limited transient response: a 1 mA to 50 mA step is handled, a 200 mA step at high edge rate is not, and a circuit that expects the second should add output capacitance rather than rely on the loop.

Buyer questions on the 3.0 V code

What is the difference between this and the TPS7A03 at 3.0 V? The quiescent current is 1 uA against 200 nA, the accuracy is 3 percent maximum against 1.5 percent, and the load transient is slower. The TPS7A05 adds the active discharge and a foldback limit; the TPS7A03 wins on standby current.

Does the three pin SOT-23 version exist for this voltage? Yes, the family lists a DBZ body without the enable pin, which is useful where the rail is permanent. The electrical limits are the same but the marking and the reel differ, so the code has to be named in full.

How much output capacitance is needed? 0.47 uF is the stability floor and 1 uF is the practical value, both ceramic with X5R or X7R dielectric. A Y5V capacitor at 3 V can lose more than half its nominal value and is not a substitute.

Buying a 1 uA regulator

Quiescent current is the one parameter distributors rarely measure, so a shipment of always on regulators deserves a spot check on a sample rather than a trust in the label. The incoming inspection plan page describes the sample sizes and the measurements we use, and safety stock planning covers how much of a 3000 piece reel a meter programme should hold against a long production run.

The foldback behaviour deserves attention before the part is chosen for an inrush load. Below the regulation point the limit falls with the output voltage, so a capacitor bank that demands 400 mA at power up sees the regulator deliver its short circuit figure of 65 mA to 150 mA until the bank charges, and the charging time is set by that current rather than by the 200 mA rating. A circuit with a large output capacitance should either accept the longer rise or add a series element. The active discharge pulls the output down when the enable pin goes low, which is what gives a microcontroller a defined reset state on a fast power cycle.