TPS7A20L18PDQNR
Product Specifications
TPS7A20L18PDQNR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS7A20L18PDQNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS7A20L18PDQNR: the 1.8 V member with a 1.2 V logic enable
The TPS7A20L18PDQNR is the 1.8 V, 300 mA output of the TPS7A20L variant, which differs from the standard TPS7A20 in one respect that decides whole products: its enable input is compatible with 1.2 V logic. On a processor whose general purpose outputs run at 1.2 V, a regulator that needs 1.4 V to enable cannot be driven directly, and a level shifter or a pull up to a higher rail has to be added. This part removes that.
Everything else follows the family: 7 uV RMS of noise, 95 dB of rejection at 1 kHz, 6.5 uA of quiescent current, a 1.6 V to 6.0 V input window, a 0.8 V to 5.5 V output window and a 1.5 percent maximum tolerance. At 1.8 V the dropout is 200 mV in the 1.5 V to 2.5 V band, so a 2.0 V source holds regulation at full load. The DQN suffix is the four pin X2SON body at 1 mm by 1 mm, and 3000 pieces ship on a large reel.
Key electrical data for the 1.8 V point
| Input range | 1.6 V to 6.0 V, 2.0 V minimum for full regulation at 300 mA |
| Output current | 300 mA, current limit 360 mA to 730 mA in this body |
| Quiescent current | 6.5 uA typical, with a smart pulldown holding the part off when enable floats |
| Accuracy | plus or minus 1.5 percent maximum over minus 40 to 125 C |
| Dropout at 300 mA | 200 mV in the 1.5 V to 2.5 V band, 140 mV at 3.3 V output |
| Rejection | 95 dB at 1 kHz into 20 mA, 60 dB at 100 kHz |
| Noise | 7 uV RMS over 10 Hz to 100 kHz with a 1 uF ceramic output capacitor |
Package, marking and reel data
| Body | X2SON DQN, 4 pins, 1.0 mm by 1.0 mm, 0.5 mm pitch |
| Reel | 3000 pieces, large tape and reel, 180 mm carrier, 8 mm tape |
| Finish | NIPDAU |
| Moisture | level 1, 260 C peak reflow, unlimited floor life |
| Marking | OW |
Where a 1.2 V logic enable matters
Modern processors and field programmable gate arrays often run their general purpose outputs at the core voltage rather than at the input output voltage, so a 1.2 V high is all the enable signal a rail will see. A regulator with a 1.0 V threshold accepts that directly; one with a 1.4 V threshold does not, and the usual workaround is a pull up to a rail that may not be alive yet, which reintroduces a sequencing fault.
The rest of the circuit is the familiar 1.8 V analog rail. From a 2.1 V buck output the part dissipates 90 mW at 300 mA and holds the rail through the converter's ripple, which is the reason to use a linear stage here rather than a second converter. From a 3.3 V rail the dissipation is 450 mW, which the 1 mm body passes only with a proper thermal pad, so a board that runs the regulator hot should either lower the input or split the load between two rails.
Buyer questions on the low threshold version
Is this part electrically identical to the standard TPS7A20 at 1.8 V? In output behaviour, yes: the same noise, rejection, accuracy and current limit apply. The enable threshold and the available bodies are the difference, so the two are not interchangeable where the enable drive is marginal.
What is the enable threshold? It is specified for 1.2 V logic, so a 1.0 V high enables the part and a 0.4 V low disables it. That is the reason the L variant exists rather than a resistor divider on the enable pin.
Can the SOT-23 version be ordered in this variant? The L variant is published in the X2SON body only. A board that needs a leaded part has to use the standard TPS7A20 and drive the enable from a rail above 1.4 V.
Sourcing the L variant
Single body variants are the first to be affected when a vendor rationalises a family, so a second source decision should be made while the part is healthy. Component shortage forecast describes the signals we watch, and pin to pin cross reference lists the alternatives by footprint.
The enable circuit is the whole difference from the standard part, and it matters at the system level. A processor whose general purpose outputs run at 1.2 V cannot drive a regulator that needs 1.4 V, and the usual workaround is a pull up to a rail that may not be alive yet, which reintroduces the sequencing fault the enable pin was meant to solve. With a 1.0 V threshold the rail can be switched directly from the processor. The rest of the specification is the family: 6.5 uA of quiescent current, 1.5 percent tolerance, 200 mV of dropout in the 1.5 V to 2.5 V band and 7 uV RMS of noise.