Contact Us

TPS7A2050PDQNR

Brand: Texas Instruments
Texas Instruments TPS7A2050PDQNR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A2050PDQNR — Power Management & Signal Chain | Superb Automation

TPS7A2050PDQNR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A2050PDQNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A2050PDQNR: a 5.0 V low noise rail from as little as 5.14 V

The TPS7A2050PDQNR is the 5.0 V fixed output of the TPS7A20 family, in the four pin X2SON body. It is the top of the family range, which reaches 5.5 V, and it delivers 300 mA with 140 mV of maximum dropout in the 2.5 V to 5.5 V band. For a 5 V analog rail fed from a 5.2 V bus, that is enough headroom to regulate, which is unusual for a part this quiet.

The use case is a 5 V sensor, a 5 V reference chain or a 5 V audio stage that has to be free of switching residue while the upstream converter is only a fraction of a volt higher. Because the input window reaches 6.0 V, the same part also works directly from a 5.5 V protected battery rail, at the cost of dissipating the difference at full load.

Key electrical data for the 5.0 V point

Input range1.6 V to 6.0 V, 5.14 V minimum for full regulation at 300 mA
Output current300 mA, current limit 360 mA to 730 mA, short circuit 160 mA
Quiescent current6.5 uA typical, 10 uA maximum
Accuracyplus or minus 1.5 percent maximum, which is 75 mV at this output
Dropout at 300 mA140 mV in the 2.5 V to 5.5 V band
Rejection95 dB at 1 kHz into 20 mA, 60 dB at 100 kHz, 45 dB at 1 MHz
Noise7 uV RMS over 10 Hz to 100 kHz, which is about 1.4 ppm of the output

Package, marking and reel data

BodyX2SON DQN, 4 pins, 1.0 mm by 1.0 mm
Reel3000 pieces, large tape and reel, 180 mm carrier, 8 mm tape
FinishNIPDAU, with G4 and M3 rows on the same code
Moisturelevel 1, 260 C peak reflow
MarkingKR

Where a 5 V low noise rail belongs

Industrial sensors, 4 to 20 mA loop transmitters, precision references and audio stages all run at 5 V and all care about noise. A 5 V rail derived from a 24 V bus through a buck converter carries the switching ripple unless something removes it, and a linear stage from a 5.2 V intermediate rail is the cheapest way to do that. The rejection of 95 dB at 1 kHz takes a 20 mV ripple down to about 0.4 uV, which is below the noise floor of most references.

The thermal number is the one that decides feasibility. At 5.5 V in and 5.0 V out the part dissipates 150 mW at full load, which the X2SON passes with a proper pad. At 6.0 V in it dissipates 300 mW, and at that point the junction rise in a 1 mm body becomes the limiting factor for continuous operation, so a product that runs from a 6 V rail should either reduce the load or move to a larger body.

Buyer questions on the 5.0 V code

Does the part regulate from a 5.1 V input? Not at full load. The maximum dropout in this band is 140 mV, so 5.14 V is the floor for 300 mA. Below that the output follows the input minus the dropout and the rail is no longer regulated.

Is the noise figure still valid at 5 V output? Yes. The 7 uV RMS figure is quoted across the family, and at 5 V it is a smaller fraction of the output than at 0.8 V, which is why 5 V rails from this part measure better in relative terms.

Which body should a 5 V rail use? The X2SON when board area matters, the SOT-23 when the assembly house needs a leaded part, and the DSBGA when the board is a module. All three are published at this trim with the same electrical limits.

Sourcing a 5 V low noise rail

A 5 V analog rail usually sits on a board that also carries a 24 V input, so the power tree is bought as a whole rather than line by line. One stop RF supply describes the combined buying route, and supplier scorecard covers how we rate the channel that ships a 3000 piece reel.

At 5 V output the 1.5 percent tolerance is 75 mV, which is the number to compare against the load's own supply window before the part is chosen. The rejection is 95 dB at 1 kHz into 20 mA and 60 dB at 100 kHz, so a 20 mV switching residue at the input becomes a fraction of a microvolt at the output, and the 7 uV RMS noise figure is about 1.4 ppm of the rail. The M3 row of the same code is the moisture level variant and the G4 row the finish variant, so the packing has to be named on the order.