Contact Us

TPS60230RGTR

Brand: Texas Instruments
Texas Instruments TPS60230RGTR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS60230RGTR — Power Management & Signal Chain | Superb Automation

TPS60230RGTR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS60230RGTR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS60230RGTR: five channel white LED charge pump current source with PWM brightness control

TPS60230RGTR is a charge pump that drives up to five white LEDs at a matched current from a single lithium cell without an inductor in a QFN (RGT) body of 16 pins. It runs from 2.7 V to 6.5 V, drives five LEDs at 25 mA each for a total of 125 mA, matches the channels to 0.4 per cent typical, and sets the current with one resistor, all in a 3 mm by 3 mm QFN.

Order code and package

Ordering stringTPS60230RGTR, the 16 pin QFN on a large reel
Body16 pin QFN, 3.00 mm by 3.00 mm, junction to ambient 52 degrees per watt
ChannelsFive current sinks, one per LED, each rated to 25 mA
ConversionFractional charge pump with a 1x mode and a 1.5x mode, switching between them as the battery falls
Current settingOne resistor on the ISET pin sets the current in every channel, with a 600 mV reference
BrightnessA PWM signal on the enable pins sets the average current from zero to the programmed maximum
Input range2.7 V to 6.5 V, which covers a single lithium cell and three or four alkaline cells

Electrical parameters that decide the application

Output current25 mA per channel, 125 mA total, from 3.1 V to 6.5 V in
Channel matching0.4 per cent typical between any two outputs at 3.1 V of LED drop and 25 degrees, 2 per cent at the extremes
Reference600 mV typical, 580 to 620 mV, on the ISET pin
Quiescent current200 uA typical in 1x mode with 20 uA on ISET, 2.1 mA in 1.5x mode
Shutdown current0.1 uA typical, 1 uA maximum
Switching frequency1 MHz typical, 0.75 to 1.25 MHz over the range
Overvoltage limit5.5 V with an LED channel left open, so an unpopulated channel does not destroy the part
Input current limit350 mA with both enables high and 100 uA on ISET
Efficiency83 per cent at 3.7 V in with 15 mA per LED and a 3.1 V LED drop
PWM dimming0 to 50 kHz on the enable pins, with a 2.5 us minimum on time, so the dimming ratio has a floor at high frequency
Start up375 us typical, with a 160 us soft start
Thermal shutdown160 degrees with 20 degrees of hysteresis

Family variants and how they differ

1x against 1.5x modeIn 1x mode the input passes through a switch and the part behaves like a linear current sink, which is efficient while the battery is above the LED drop plus headroom. Once the battery falls, the pump switches to 1.5x and doubles the current draw from the input
Why 1.5x and not 2xA 1.5x pump keeps efficiency higher across the lithium discharge curve at the cost of a mode transition in the middle of the curve, which shows as a small step in brightness unless the transition is filtered
ISET resistorEvery channel current is set by one resistor, so channel to channel matching does not depend on five resistors. The tolerance of that one resistor sets the absolute current for all five LEDs
PWM dimmingThe enable pins accept a PWM signal, so brightness dims without changing the ISET resistor. Below a few percent duty the 2.5 us minimum on time limits how deep the dimming goes
Open channel handlingThe overvoltage limit at 5.5 V protects the part when a channel is unconnected, which happens on a panel variant with four LEDs instead of five
Against a boost driverA boost LED driver is more efficient for long strings at high current. This pump is for short strings where the inductor and its field are the problem, not the efficiency

Points to check before this part goes on a BOM

The 25 mA per channel figure holds from 3.1 V in. Below that the pump is in 1.5x mode and the input current doubles, so a weak cell sees a 250 mA draw for 125 mA of LED current.

Current matching is 0.4 per cent typical, not maximum. A panel that must have uniform brightness across five strings should be checked at the extremes of temperature, where the figure widens to 2 per cent.

The ISET resistor sets all five currents. Its tolerance and its temperature coefficient become the brightness tolerance of the whole display, which is why a 0.1 per cent part is normal here and a 5 per cent part is not.

The input current limit is 350 mA. In 1.5x mode with all five LEDs at 25 mA the input current approaches that limit, so the maximum brightness available from a nearly empty cell is lower than from a full one.

Dimming below a few per cent duty is limited by the 2.5 us minimum on time. A product that needs deep dimming for night operation uses a lower ISET current rather than a very short pulse.

An unconnected channel is protected by the 5.5 V overvoltage limit, but the part does not report which channel is open. A bench check with one LED removed is the usual way to confirm the behaviour before a panel variant is released.

Where a charge pump beats a boost converter

A boost LED driver needs an inductor, a switch node and a board region where the switching loop stays small. On a display connector that sits beside a cellular antenna, that switching node is a radiator. A charge pump moves charge with flying capacitors at a lower edge rate and no inductor, and the radiated field is smaller and easier to control.

The price is efficiency and headroom. Fractional conversion at 1.5x is less efficient than a good inductive boost, and the part needs the input to stay above the LED drop plus a margin in 1x mode. For a five LED backlight at 25 mA, that trade is usually worth taking.

Where this order code fits

Colour display backlights in handheld instruments, portable medical devices, barcode scanners, POS terminals and small panel displays. A charge pump is chosen over a boost converter where the LED string is short and the panel is small, because it removes the inductor and the associated radiated field, which matters when the display sits next to a radio or an ADC. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

Can it drive four LEDs instead of five? Yes. The unused channel can be left open, and the 5.5 V overvoltage limit protects the part. The current in the other channels does not change, because each channel is an independent current sink.

How is the LED current set? By a resistor on ISET against a 600 mV reference. The same current flows in every channel, so one resistor sets the whole display.

What happens when the battery falls below the LED forward voltage? The pump switches from 1x to 1.5x, the input current roughly doubles for the same LED current, and efficiency drops. That transition is where the input current limit can bind.

Is PWM dimming audible? At 1 kHz to 20 kHz, no. Below a few hundred hertz some ceramics can sing, and the 0 to 50 kHz range means the dimming frequency is a choice rather than a fixed value.

Does it need an inductor? No. Two flying capacitors and the output capacitor are the only energy storage parts, which is the reason to use it in a display that sits near a radio.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Date Code Management page sets out the checks that keep a substitute from failing on the bench.