Contact Us

LTC2386IUH-16#TRPBF

Brand: Analog Devices
Analog Devices LTC2386IUH-16#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTC2386IUH-16#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LTC2386IUH-16#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTC2386IUH-16#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

LTC2386IUH-16#TRPBF: 10 Msps, 16 Bits, and 3.2 Picoseconds of Clock Jitter

The LTC2386IUH-16#TRPBF is a 16-bit 10 Msps successive approximation converter with no pipeline delay and no cycle latency. Signal to noise ratio is 93.8 dB typical at a 1 MHz input, spurious free dynamic range is 102 dB, the input is an 8.192 V peak to peak differential signal sampled at up to 5 MHz, integral nonlinearity is plus or minus 0.5 LSB maximum with no missing codes, the supplies are 5 V and 2.5 V, the internal reference is 20 ppm per degree C maximum, the digital interface is serial LVDS in one or two lane mode, power dissipation is 97 mW, and the package is a 32-lead 5 mm by 5 mm QFN.

The part is bought for two things: a conversion that lands in the same cycle it was started, which is what a control loop needs, and an analogue front end that stays linear at high input frequencies. A pipelined converter with latency forces the loop to account for the delay, and a converter with a wide input network stops being 16-bit at 1 MHz.

Ninety-three point eight decibels is 15.3 effective bits

The signal to noise ratio converts to 15.29 effective bits at a 1 MHz input, so one bit of the sixteen is spent on noise and distortion that the data sheet already accounts for. The 102 dB spurious free dynamic range is 17 bits of headroom over the same signal, which means the limit is broadband noise rather than a harmonic, and that is the better place for it: noise can be averaged down, a spurious tone cannot.

There is nothing to average in a 10 Msps stream at full rate, so the 15.3 bits is the working resolution. A customer who needs the full 16 bits has to either reduce the input frequency, where the noise figure improves, or accept that the last bit is a statistical quantity.

The same 93.8 dB at 5 MHz would need 0.65 ps of clock jitter

At a 1 MHz input, 93.8 dB of signal to noise corresponds to 3.2 ps of clock jitter. The jitter requirement scales inversely with input frequency, so the same ratio at the 5 MHz Nyquist limit needs 0.65 ps. That number is below what a general purpose clock buffer delivers, which means the clock source, not the converter, sets the achievable ratio at the top of the band. A crystal oscillator with sub-picosecond jitter and a short, terminated clock trace is part of the 16-bit claim at 5 MHz.

The internal reference is 20 ppm per degree C, which over 165 degrees is 0.33 percent, 27 mV on the 8.192 V span, or 216 codes. If the conversion has to be absolutely accurate rather than relatively linear, the internal reference is the dominant term by two orders of magnitude over the 62.5 uV of a half code, and an external reference is the answer.

Resolution and rate16 bit, 10 Msps, no pipeline delay, no cycle latency
Dynamic range93.8 dB signal to noise at 1 MHz, 15.29 effective bits, 102 dB spurious free
Input8.192 V peak to peak differential, Nyquist to 5 MHz, 125 uV per code
LinearityPlus or minus 0.5 LSB maximum, 62.5 uV, no missing codes
Jitter budget3.2 ps at 1 MHz, 0.65 ps at 5 MHz for the same 93.8 dB
ReferenceInternal 20 ppm per degree C, 0.33 percent over 165 degrees, 216 codes
Supplies and power5 V and 2.5 V, 97 mW, 19.4 mA from the 5 V rail
InterfaceSerial LVDS, one lane at 160 Mbps or two lanes at 80 Mbps each
Package32-lead QFN, 5 mm by 5 mm
ApplicationsImaging, high speed data acquisition, control loops, communications, ATE

Two questions buyers ask

Is the internal reference good enough for a 16-bit absolute measurement?
No. Twenty ppm per degree C over the industrial range is 0.33 percent, which is 216 codes of the 16-bit span. The internal reference is fine for a relative measurement or for a loop, where the ratio is what matters. An absolute measurement needs an external reference with a few ppm per degree C and the same attention to its own settling.

One LVDS lane or two?
One lane carries 160 Mbps at 10 Msps and two lanes carry 80 Mbps each. The choice is made by the receiver, not by the converter: two lanes halve the bit rate per pair and relax the PCB loss budget, at the cost of one more pair and a second deserialiser channel. Both modes put the same data on the wire and the converter's performance does not change.

Ordering and supply

The IUH suffix is the 32-lead QFN on the industrial grade and the -16 marks the 16-bit member of the family. The same body is offered at other resolutions and rates, so the part number carries the resolution and the speed and neither is implied by the package. The reference grade and the interface mode are set by the board, not by the order code.

We source this family for production and for repair lots. Start at the analog mixed signal ICs family page, compare a candidate against the ADC and DAC cross reference, and where a converter has to replace one that is no longer available, pin to pin cross reference shows how the interface lanes, the reference pins and the supply rails line up before any board work starts.

Request Quote — In Stock, 100% New & Original, Full Warranty