LTC2662IUH-16#TRPBF
Product Specifications
LTC2662IUH-16#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTC2662IUH-16#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LTC2662IUH-16#TRPBF: Five 300 mA Current Sources and the 4.6 uA Code That Sets the Job
The LTC2662IUH-16#TRPBF is a five-channel, 16-bit current-source-output converter. Each channel has eight programmable full-scale ranges, 300 mA, 200 mA, 100 mA, 50 mA, 25 mA, 12.5 mA, 6.25 mA and 3.125 mA, and 1 V of dropout is guaranteed at 200 mA, so the load may sit as high as the channel supply minus that volt. Every output has its own supply pin, 2.85 V to 33 V, and internal switches can pull any output to an optional negative rail. The integrated reference is 1.25 V at 10 ppm per degree C maximum, an external reference may be used instead, the serial interface runs to 50 MHz on logic levels down to 1.71 V, an analog multiplexer lets the host read back output voltages and currents, and the package is a 5 mm by 5 mm 32-lead QFN. The vendor lists the part as recommended for new designs.
This is the part that removes the sense resistor and the current-regulating amplifier from a bias circuit. A laser, a semiconductor optical amplifier, a resistive heater or a proportional solenoid all want a current, not a voltage, and the usual discrete loop costs an amplifier, a shunt, four resistors and a stability question. Here the current is set by a code and the loop is inside the package.
One code is 4.6 uA at 300 mA and 47.7 nA at 3.125 mA
Range selection is the resolution control, not the bit count. Sixteen bits over a 300 mA span gives 4.578 uA per code. Sixteen bits over the 3.125 mA span gives 47.68 nA per code, which is 96 times finer for the same converter and the same interface. A channel that has to trim a 2 mA laser bias to 10 uA therefore belongs on the 3.125 mA or 6.25 mA range, where the step is comfortable, and a channel that has to drive 250 mA should be on the 300 mA range and accepts 4.6 uA steps. The 12-bit version of the same part gives 73.2 uA per code on the 300 mA range, so the difference between the two order codes is 16 times the trim granularity.
The eight ranges are set per channel, so a five-channel board can hold a 300 mA pump, a 25 mA heater and three 3.125 mA bias trims at the same time without any external gain switching. That is the practical reason to buy five channels rather than five single devices.
One volt of dropout at 200 mA is where the heat goes
The compliance range is wide and that is exactly what makes the thermal arithmetic unforgiving. Driving 200 mA into a 5 V load from a 24 V rail leaves 19 V across the output device, which is 3.8 W inside a 5 mm by 5 mm package. The same 300 mA into a 32 V load from a 33 V rail leaves 1 V, which is 0.3 W. Two customers with the same part number and the same current can be 12 times apart on dissipation, and the difference is the load voltage, not the current.
Where the drop cannot be reduced, a series resistor outside the package moves part of the heat off the die at the cost of compliance headroom, and the resistor has to be sized for the worst-case current, not the nominal one. The exposed pad is the only thermal path, so the copper under the part is part of the current rating, and a board that quotes 300 mA per channel without checking the load voltage will find the limit on the bench rather than on the data sheet.
| Channels | Five current-source outputs, 16 bit or 12 bit by order code |
| Ranges | 300, 200, 100, 50, 25, 12.5, 6.25 and 3.125 mA, programmable per channel |
| Resolution | 4.578 uA per code on 300 mA, 47.68 nA per code on 3.125 mA |
| Dropout | 1 V guaranteed at 200 mA, load to 32 V |
| Supplies | 2.85 V to 33 V per channel, optional negative supply through internal switches |
| Reference | Internal 1.25 V at 10 ppm per degree C maximum, or external |
| Drift over 165 C | 0.165 percent, which is 495 uA or 108 codes at 300 mA |
| Parallel operation | Five channels sum to 1.5 A, 22.9 uA per code at that sum |
| Interface | SPI to 50 MHz, logic from 1.71 V, A/B toggle by pin or command |
| Monitoring | Analog multiplexer for output voltage and current readback |
| Package | 32-lead QFN, 5 mm by 5 mm, minus 40 to 125 C |
Two questions buyers ask
Can I sum the channels to reach 1.5 A?
Yes, five channels at 300 mA sum to 1.5 A, and the summed code resolution is 22.9 uA at 16 bits. The split between the five outputs follows the resistance of the routing to the star point rather than the code, so equal length traces and a single summing node are what keep the sharing even. The channels also share one reference, so the sum tracks drift as one number rather than five.
Does it need a negative supply?
No for a grounded load. The optional negative rail exists so an output can be pulled below ground through the internal switch, which matters for a laser or a diode whose anode is grounded and whose cathode must sit at a negative bias. A board that never goes below ground leaves that pin unconnected and the part behaves as a plain current source.
Ordering and supply
The IUH suffix is the 32-lead QFN, the -16 is the 16-bit grade, and the TRPBF suffix is tape and reel, lead free. The 12-bit grade shares the package and the pinout but not the resolution, so an order placed on a package description alone can deliver a converter with 16 times the code size. The temperature grade and the reference drift are on the same order line and both matter in a laser bias loop.
We source this family for production builds and for repair lots. Start at the analog mixed signal ICs family page, compare a candidate against the ADC and DAC cross reference, and where a bias converter has to go into a board that is already built, the sequence in how to verify a drop in replacement puts the full-scale range and the power-up state ahead of the socket check.
Request Quote — In Stock, 100% New & Original, Full Warranty