Contact Us

TPS54160ADRCR

Brand: Texas Instruments
Texas Instruments TPS54160ADRCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54160ADRCR — Power Management & Signal Chain | Superb Automation

TPS54160ADRCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54160ADRCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54160A 60 V 1.5 A converter for 48 V buses and industrial rails

The TPS54160ADRCR is the 60 V member of the same 1.5 A family as the 42 V TPS54140A, in the 10 pin VSON 3 mm by 3 mm body or the MSOP body of the same footprint. It takes 3.5 V to 60 V in, delivers 1.5 A, and uses a 200 milliohm high side switch with a 0.8 V reference. The extra 18 V of input rating over the 42 V part is what opens up 48 V telecom and industrial buses, where a nominal 48 V rail with a transient can reach 58 V and would exceed a 42 V part.

The A suffix carries the same tightening as on the 42 V part: the enable window is 1.11 V to 1.36 V here against 0.9 V to 1.55 V on the plain TPS54160. In the same datasheet the two rows sit next to each other, which is a useful reminder that the base number alone does not identify the enable behaviour.

Key parameters taken from the SLVSB56C document

Input range3.5 V to 60 V operating, with an internal UVLO at 2.5 V
Output current1.5 A, with 200 milliohm typical and 410 milliohm maximum high side resistance at 12 V in, and 300 milliohm at 3.5 V in
Switching frequency100 kHz to 2.5 MHz set by the RT/CLK resistor, synchronisable to an external clock
Reference0.8 V, 0.792 V to 0.808 V at 25 degrees and 0.784 V to 0.816 V over minus 40 to plus 150 degrees
Quiescent current116 microamp typical and 136 microamp maximum while not switching, 1.3 microamp typical and 4 microamp maximum in shutdown
Enable pin1.11 V to 1.36 V on the A suffix against 0.9 V to 1.55 V on the plain suffix, with 3.8 microamp of input current
Power goodOpen drain, asserted outside 94 to 107 per cent of nominal output
ProtectionCycle by cycle current limit, frequency foldback, thermal shutdown
Thermal10 pin VSON and 10 pin MSOP bodies with an exposed pad, the VSON being the better thermal path
ESD2000 V human body model and 500 V charged device model

Duty cycle, minimum on time and the 60 V input

At 60 V in and 3.3 V out the duty cycle is about 5.5 per cent, and at 2.5 MHz the on time is 22 nanoseconds, which is below the minimum on time of most converters in this class. That is the real constraint on a 60 V to 3.3 V rail: the frequency has to come down, or the input has to be pre regulated, or the output has to be higher. The vendor's typical application circuits for the wide input case run at 300 kHz to 500 kHz for exactly this reason. A rail built at 2 MHz from 60 V will skip pulses and show a higher ripple than the calculation predicts.

Input voltage derating and the transient margin

The 60 V rating is a recommended maximum with a 65 V absolute maximum on the input pin. A 48 V bus with a 20 per cent transient reaches 58 V, which leaves 2 V of margin to the recommended limit and 7 V to the absolute limit. A bus that sees a load dump, such as an automotive 24 V system, needs a transient suppressor ahead of the converter, because a load dump will exceed the absolute maximum and no amount of copper will save the part.

Compensation and the physical arrangement of the switching loop

The part is current mode, so the compensation is a type two network on COMP, and the loop is set by the output capacitor and the inductor. What matters physically is the area of the loop formed by the input capacitor, the high side switch and the low side path. At 500 kHz and 1.5 A the current in that loop changes by amps in tens of nanoseconds, so the input capacitor has to sit within a few millimetres of the VIN and ground pads, and the return path should be a plane rather than a trace. The exposed pad is the thermal path and also the quiet ground, and it should be connected to the ground plane with vias under the body.

Where the part is used and what a quote should name

Typical sockets are 48 V telecom line cards, 24 V and 48 V industrial backplanes, and bias supplies in motor drives where the 60 V rating covers the back EMF. The 1.5 A ceiling is what positions the part: it is a housekeeping or bias regulator, not a main payload rail.

A quote should name the suffix and the body. The A suffix changes the enable window, the VSON and MSOP bodies change the thermal path, and the reel size changes the line side. Our desk quotes the three fields together, and where the exact combination is short we show the 42 V family member and the wider grade alternatives side by side on power management cross reference and pin to pin cross reference.

Frequently asked questions

Can the output be set to 0.8 V. Yes, that is the reference, and the minimum on time then becomes the limit at high input voltage. A 0.8 V rail from 60 V in is a 1.3 per cent duty cycle, which at 500 kHz is 27 nanoseconds and at the edge of what the part can hold.

Is the plain suffix still available. The datasheet covers both, but a program that qualified on the A suffix should not accept the plain part, since the enable window differs. Our desk keeps the two apart on the quote so the difference cannot be lost in a substitution. See how to verify a drop in replacement for the checks that apply.