VBI1314
Product Specifications
VBI1314
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBI1314 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBI1314: 30 V and 8.7 A in a SOT89
The VBI1314 is a single N channel MOSFET in a SOT89 body, rated at 30 V drain to source, plus or minus 20 V on the gate, a 1.7 V threshold, 8.7 A of drain current, 18 milliohm at a 4.5 V gate and 14 milliohm at 10 V. It is a small, low voltage, logic level switch.
30 V is the class for a 12 V rail with margin, for a 24 V rail without much transient, and for the output of a small buck converter. At 14 milliohm the loss at 3 A is 0.13 W, which a SOT89 tab can remove, and at 6 A it is 0.5 W, which it can still remove with a decent pad. That is the working range.
The 1.7 V threshold makes it a logic level part with room to spare. A 3.3 V output drives it past threshold with a real overdrive and a 5 V output uses the published 4.5 V column almost exactly.
Key data for the VBI1314
| Configuration | Single N channel |
| Package | SOT89, three leads and a drain tab |
| VDS | 30 V |
| VGS | Plus or minus 20 V |
| Vth | 1.7 V typical |
| ID | 8.7 A, a die figure |
| RDS(on) at 4.5 V | 18 milliohm |
| RDS(on) at 10 V | 14 milliohm |
| Technology | Trench |
| Loss at 2 A, 4.5 V gate | 0.072 W through the channel |
| Loss at 5 A, 4.5 V gate | 0.45 W through the channel |
| Thermal path | Drain tab into the copper |
18 and 14 milliohms: what the gap tells you
The 22 per cent difference between the 4.5 V and 10 V columns says the die is close to fully enhanced at 4.5 V and does not gain much from a higher gate voltage. For a part used on a 5 V rail that is exactly the behaviour wanted: the resistance in the circuit is close to the best the die can do, and the gate drive can be a logic output.
It also means a 3.3 V gate is only a little worse than 4.5 V. The threshold is 1.7 V, so 3.3 V gives 1.6 V of overdrive, which for a 30 V trench die is enough to be near the knee. The resistance at 3.3 V is not printed, and it will be somewhat above 18 milliohm rather than far above it.
The 20 V gate window is the ordinary one. On a 24 V rail the gate must not be pulled below the source by more than 20 V, which in a high side arrangement with the source at 24 V means the gate cannot go to ground. A divider or a zener handles it.
One more thing about this body: the tab is the drain and it is also where the heat leaves. A tab tied to a switching node cannot sit on a large ground pour, so the copper under it is a small island connected to the rail. That limits the thermal area to what can be built around the node, which is why the practical current figure for a SOT89 is lower than the same die would give in a body with an isolated pad. It is a package limit, not a silicon one.
A SOT89 as a load switch on a 12 V rail
A SOT89 is a good size for a load switch that has to pass 2 to 5 A on a 12 V rail. The tab gives a thermal path, the footprint is small, and the part is cheap. What it does not give is a low resistance at high current: at 8 A the loss is 1.15 W and the tab needs a pad well beyond its outline.
The body diode matters in a load switch that feeds an inductive load. When the switch opens, the load current continues through the diode to the rail, which is fine if the rail can absorb it and not fine if the rail is a battery that cannot. A freewheel diode across the load is the usual addition, and it is cheaper than a bigger switch.
The gate has to be held off when the driver is unpowered. A 1.7 V threshold is low enough that a floating gate picks up charge and turns the load on, so a 10 kohm resistor from gate to source is not optional on this part.
Where the part fits and where it does not
It fits a load switch on a 12 V rail at 2 to 5 A, a small motor or fan driver, a level shift for a 24 V signal, a reverse polarity switch at low current, and a synchronous rectifier in a small buck at 12 V to 5 V. It does not fit a 24 V rail with a load dump, a 48 V rail, or a current path above 6 A continuous.
For a logic level part on a 12 V rail, the two things that decide whether a substitute works are the resistance at 3.3 or 5 V and the gate pull down. Our how to reduce component cost page covers where a lower cost equivalent can be used and where the loss it adds outweighs the price difference.
The sourcing side of this part is covered on the BOM scrubbing. For a small logic level switch used in several places on one board, that page covers how the BOM is cleaned before the order.
Questions we get on this code
Can a 3.3 V pin drive it? Yes. The threshold is 1.7 V and the resistance at 3.3 V is a little above the 4.5 V column, which is fine at a few amps.
How much current on a normal board? 2 to 5 A with a pad larger than the tab. At 8 A the loss is over a watt and the part runs hot.
Does it need a gate resistor? A 10 kohm pull down is needed to keep it off. A series resistor of a few ohms slows the edge where ringing is a problem.
What should a purchase order carry? Part number, SOT89, and the reel quantity. We confirm the packing on the offer.