VBGQT1101
Product Specifications
VBGQT1101
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBGQT1101 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBGQT1101: 100 V and 350 A in the TOLL body
The VBGQT1101 is a single N channel MOSFET in a TOLL body, rated at 100 V drain to source, plus or minus 20 V on the gate, a 3 V threshold, 350 A of drain current and 1.2 milliohm at a 10 V gate. The TOLL is a leadless surface mount package in which the source and drain are large clips rather than thin legs.
The package is the story here. In a conventional body the current leaves through a lead that is a fraction of a millimetre thick, and at 350 A that lead is the limit. In a TOLL the clip is the terminal, so the current path from the die to the board is short and wide, and the resistance and the inductance of the connection both fall.
100 V is the class for a 48 V or 72 V rail with a real transient allowance, for a 60 V battery, and for the output stage of a converter that feeds a 48 V bus. At 1.2 milliohm the conduction loss at 100 A is 12 W, which is why the clip matters as much as the die.
Key data for the VBGQT1101
| Configuration | Single N channel |
| Package | TOLL, leadless, clip terminals |
| VDS | 100 V |
| VGS | Plus or minus 20 V |
| Vth | 3 V typical |
| ID | 350 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 1.2 milliohm |
| Technology | Shielded gate trench |
| Loss at 50 A | 3 W through the channel |
| Loss at 100 A | 12 W through the channel |
| Body diode | Intrinsic, cathode at the drain |
| Thermal path | Drain clip to the copper, source clip to the copper |
What a clip package changes in the power loop
A conventional package has a lead of a few nanohenries in the source path. At 350 A and a 30 ns edge the voltage across that inductance is tens of volts, and it subtracts from the gate drive exactly when the die is trying to turn on. A clip package removes most of it, so the same die switches faster and with less gate drive.
The clip also lowers the resistance from the die to the board, which at 1.2 milliohm is a real fraction of the total. The gain is not in the die but in the connection, and it is the reason a 1.2 milliohm TOLL part measures closer to its catalogue value on a board than a 1.2 milliohm part in a leaded body does.
The cost is the assembly. A leadless clip package needs a good stencil, a flat board and a reflow profile that does not leave voids under two large pads. Voiding under the drain clip is the usual cause of a part that runs hot, and it is invisible without an X ray.
There is a thermal detail specific to a clip part: the clip covers the whole die, so the heat leaves through a large area, but the pad under it has to spread that heat into copper that is usually thinner than the clip. The spreading resistance across a heavy pad on two ounce copper is a small number in milliohms and a large number in degrees per watt, and it is the term that decides whether 12 W can be removed at 100 A. A metal core board, or a copper block under the part, is the usual answer above 50 A and it is a mechanical decision made long before the part is chosen.
Current sense and the source connection
At 350 A a current sense across the switch is a real problem. The die is 1.2 milliohm, and a sense trace that shares a millimetre of copper with the main current has a measurable error. A Kelvin connection taken from the source clip, with its own trace back to the sense amplifier, is the only way to keep the error small.
Where the sense is taken from the board instead of the clip, the copper temperature coefficient becomes part of the measurement: 0.4 per cent per degree on a copper shunt is 40 per cent over 100 degrees, and the amplifier has to be compensated or the current limit drifts.
The source clip also carries the gate return. A gate loop that closes through the source clip and the board has an inductance that the driver has to charge, and at these currents the loop area is what sets the switching loss.
Where the part fits and where it does not
It fits the low side of a 48 V to 12 V converter at high current, an ORing switch on a 48 V bus, a battery disconnect on a 60 V pack, the output stage of a 48 V motor drive, and a hot swap switch on a 48 V backplane. It does not fit a 96 V pack without derating, a 110 V bus, or a board whose assembly process cannot hold a flat leadless part.
For a clip package at high current, the things that matter are the pad flatness, the voiding and the sense point. Our one stop BOM sourcing page covers how a group of parts around a power stage is bought on one order with the packing the line needs.
The sourcing side of this part is covered on the supplier scorecard. For a clip package part bought in volume, that page covers what is measured on the source over a quarter.
Questions we get on this code
Is a TOLL part harder to assemble? It needs a good stencil and a flat board. Once the process is set, it is no harder than any large exposed pad part.
Can it carry 350 A? Through the clips on a heavy copper board with a proper thermal path, close to it for short pulses. Continuous current is set by the copper, not by the die.
What gate drive does it need? A 10 V rail with a driver that can deliver an amp, and a gate resistor chosen for the loop inductance rather than for the die.
What should a purchase order carry? Part number, TOLL, and the reel quantity. We confirm the packing on the offer.