VBGQT11505
Product Specifications
VBGQT11505
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBGQT11505 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBGQT11505: 150 V and 170 A in a TOLL body
The VBGQT11505 is a single N channel MOSFET in a TOLL body, rated at 150 V drain to source, plus or minus 20 V on the gate, a 3.5 V threshold, 170 A of drain current and 5 milliohm at a 10 V gate. It is the 150 V member of the TOLL family, aimed at rails above 60 V where the 100 V part runs out of margin.
150 V covers a 96 V battery, a 110 V DC bus, and a 72 V pack with a wide allowance for charging and regeneration. In a converter fed from 96 V and delivering 24 V at high current, the switch sees 96 V plus the ringing on a fast edge, and 150 V is the class that holds that with a clamp.
The TOLL body matters more at this voltage than at 100 V, because the same current has to move with a higher voltage standing on the die. The clip terminals keep the source inductance low, which keeps the turn off fast without pushing the drain spike up, and that is the balance the higher voltage class needs.
Key data for the VBGQT11505
| Configuration | Single N channel |
| Package | TOLL, leadless, clip terminals |
| VDS | 150 V |
| VGS | Plus or minus 20 V |
| Vth | 3.5 V typical |
| ID | 170 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 5 milliohm |
| Technology | Shielded gate trench |
| Loss at 20 A | 2 W through the channel |
| Loss at 50 A | 12.5 W through the channel |
| Body diode | Intrinsic, cathode at the drain |
| Derating at 80 per cent | 120 V continuous working voltage |
The turn off spike at 150 V and how the package helps
The drain spike is set by the current, the loop inductance and the speed of the edge. A faster edge makes a higher spike, so there is a trade between switching loss and voltage stress. A clip package lowers the source inductance, which lets the die turn off fast without the gate being pulled back on, and the spike that remains is set by the power loop, not by the package.
That means the effort should go into the power loop. A loop of 10 nH at 50 A and a 20 ns fall gives about 25 V of overshoot, and a 96 V rail becomes 121 V against a 150 V ceiling. A loop of 20 nH doubles it, and the part is at 146 V with no margin left for the snubber.
The body diode is the second contributor in a bridge. When the opposite switch forces the diode to conduct and then pulls it off, the recovery current adds to the spike. At 150 V a slow diode is felt in the voltage margin rather than only in the loss.
A second point at this voltage is the gate drive reference. The source clip is the reference for the gate, and it also carries the load current, so a drive that references the board instead of the clip sees the clip inductance in series. That error is what turns a clean turn off into a slow one, and it is the reason the driver return should land on the source clip pad rather than on a convenient ground plane. At a 20 ns edge the difference is a few volts of gate drive, which is the difference between a clean turn off and a slow one.
Thermal behaviour of a clip package
The drain clip is the thermal path as well as the electrical one. At 12.5 W the clip, the solder and the copper have to carry the heat out of a die that is a few millimetres across, and the spreading resistance is what sets the case temperature. A clip package is better than a leaded body at this because the whole clip face is in contact with the pad.
The voiding under the clip is the failure mode to watch. A void under the centre of the die raises the junction temperature without changing the reading on a thermocouple at the edge of the package, and it is the reason the first article should be X rayed rather than measured.
At 20 A the part loses 2 W and needs very little. At 50 A it needs a heavy pad and a plane, and at 100 A it needs a heatsink through the board or a metal core.
Where the part fits and where it does not
It fits a 96 V to 24 V converter at high current, the low side of a motor drive on a 96 V pack, a battery disconnect on a 110 V string, an ORing switch on a 96 V bus, and the synchronous rectifier of a converter whose output is 48 V at 50 A. It does not fit a rectified 220 V main, a 150 V bus at full derating, or a converter at 100 kHz where the switching loss of a large die dominates.
For a 150 V switch in a clip package, the questions that decide the build are the loop inductance, the voiding under the clip and the sense point. Our supplier quality audit page covers what is checked at the source before a reel is released to the line.
The sourcing side of this part is covered on the date code management. For a part held in stock between builds, that page covers how the age of a reel is tracked and when it is set aside.
Questions we get on this code
Can it replace a leaded 150 V part? Electrically close, mechanically different. The clip needs a flat pad and a stencil that lays down an even deposit.
Does it need a snubber? At 96 V and 50 A, yes, unless the loop is very tight and the edge is slowed with a gate resistor.
How much current at 25 C ambient? About 30 A with a heavy pad and a plane, based on 4.5 W of loss. Above that the copper is the limit.
What should a purchase order carry? Part number, TOLL, and the reel quantity. We confirm the packing on the offer.