Contact Us

VBGL1803

Brand: VBsemi
VBsemi VBGL1803 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBGL1803 — Discrete & Power Semiconductors | Superb Automation

VBGL1803

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBGL1803 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBGL1803: 80 V and 180 A in the same TO263 footprint

The VBGL1803 is a single N channel MOSFET in a TO263 body rated at 80 V drain to source, plus or minus 20 V on the gate, a 3 V threshold, 180 A of drain current and 3.1 milliohm at a 10 V gate. It is the low voltage, high current member of the same family as the 100 V and 250 V parts, in the same package and with the same footprint.

80 V is the standard choice for a 48 V system. A lead acid or lithium pack at 48 V nominal reaches about 58 V at the top of charge, a load dump transient on a vehicle rail reaches higher, and the derating rule most programmes apply puts an 80 V part at 64 V continuous. That covers a 48 V pack, a 60 V PoE rail and a 48 V telecom rectifier output with room for the ringing on a fast switching node.

A 180 A die in a TO263 is the interesting part of this page. The die is large enough that the current column is not the limit, the tab is. The resistance is low enough that the loss at 40 A is only 5 W, so the problem moves from the silicon to the solder joint, the copper spreading under the tab and the way the current enters and leaves the package.

Key data for the VBGL1803

ConfigurationSingle N channel
PackageTO263, tab soldered to the board
VDS80 V
VGSPlus or minus 20 V
Vth3 V typical
ID180 A, a die figure at a 25 C case
RDS(on) at 10 V3.1 milliohm
TechnologyShielded gate trench
Body diodeIntrinsic, cathode at the drain
Loss at 40 A5 W through the channel
Thermal pathTab only, no lead frame cooling worth counting
Gate chargeNot printed on the catalogue page, ask for the curve at the working voltage

Where 3.1 milliohm changes the decision

At 3.1 milliohm the conduction loss stops being the reason to look at a bigger package. A 20 A load loses 1.2 W, a 40 A load loses 5 W, and a 60 A load loses 11 W. Those numbers are small enough that the switching loss, the gate drive and the thermal path take over as the things that decide whether the circuit works, and the choice between this part and a 5 milliohm alternative becomes a question about gate charge and cost rather than about heat.

The other side of a very low resistance is that the current sharing in a parallel bank becomes harder. Two 3.1 milliohm dies in parallel give 1.55 milliohm, and the copper between the two sources is easily 0.2 milliohm, which is 13 per cent of the total. That is enough to send most of the current through one die at the start of a pulse. A parallel bank at this resistance needs a symmetric bus bar or a deliberate resistance in each source leg.

The 3 V threshold is low enough to be driven from a 5 V logic output through a resistor at low current, but the resistance column is a 10 V column. Driving the gate at 5 V leaves the die partly enhanced and the published 3.1 milliohm does not apply. For a 100 kHz converter with a 12 V driver rail there is no issue; for a 5 V microcontroller pin driving the gate directly there is.

The 80 V ceiling in a real 48 V system

An 80 V part on a 58 V pack leaves 22 V. That sounds tight, and it is the reason the 100 V class exists for the same application. What decides between them is the transient: a battery disconnect that opens under load puts the pack inductance into the drain node, and the peak can pass 80 V for a moment. A clamp diode or a transient suppressor across the switch is the usual answer, and it is cheaper than moving the whole line to 100 V.

Ringing is the other contributor. A 40 A switch with a 20 nH loop and a fast turn off produces a peak that depends on the di/dt and the capacitance at the node, and it is easy to add 15 V to the bus for 30 ns. The fix is the copper and the gate resistor, not the voltage rating, because a higher rated part with a slower body diode can ring worse.

For a 60 V PoE or a 48 V telecom rail the margin is comfortable and the part is a straight fit. For an automotive 48 V rail the load dump requirement has to be checked against the 80 V ceiling before the part is chosen, since the standard transient for that rail is higher than the steady state.

Where the part fits and where it does not

It fits a 48 V battery disconnect, the synchronous rectifier of a 12 V output converter fed from 48 V, the low side of a motor drive on a 36 V or 48 V pack, an ORing switch on a 48 V bus, and the main pass element of a 48 V electronic fuse at currents that a single tab can spread. It does not fit a 96 V pack, a 110 V DC bus or anything derived from a rectified main, and at continuous currents above about 60 A the tab and the copper become the limit before the die does.

For a disconnect on a 48 V pack the deciding parameters are the resistance at the gate voltage the driver actually delivers and the energy the body diode has to take when the load is inductive. Our how to verify a drop in replacement page sets out the checks that decide whether a candidate behaves like the original in that position.

The sourcing side of this part is covered on the PCBA quote checklist. For a part that goes onto an assembled board, that page lists what a quote has to state so the offer and the build agree.

Questions we get on this code

Is 180 A a current I can use? Not through a TO263 on a normal board. The figure is a die rating at a 25 C case. The tab, the solder and the copper decide the real number, and on two ounce copper with vias into a plane the usual working figure is a third to a half of the printed one.

How much copper does the tab need? Enough that the spreading resistance is small against 3.1 milliohm, which on two ounce copper means a pad well beyond the tab outline and a set of vias into an inner plane. A pad the exact size of the tab is the usual cause of a part that runs hotter than the calculation says.

Can it replace a 100 V part on a 48 V rail? Yes where the transients are clamped, and no where the load dump is not limited. The footprint is the same, so the swap is easy to make and easy to regret if the clamp is missing.

What should a purchase order carry? Part number, TO263, and the packing the line can take. We confirm the reel quantity on the offer rather than assuming it.