Contact Us

VBK8238

Brand: VBsemi
VBsemi VBK8238 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBK8238 — Discrete & Power Semiconductors | Superb Automation

VBK8238

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBK8238 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBK8238: a 20 V P channel at 4 A in SC70-6

The VBK8238 is a single P channel MOSFET in a SC70-6 body rated at minus 20 V drain to source, plus or minus 20 V on the gate, a minus 0.6 V threshold, minus 4 A of drain current, 45 milliohm at a 2.5 V gate and 34 milliohm at a 4.5 V gate. Thirty four milliohm in a body two millimetres by two millimetres is a low resistance die for this package.

The current column reads 4 A. At 34 milliohm that is 0.54 W, and a SC70-6 with six small leads has no tab. The die can pass 4 A; the body removes about a tenth of a watt without help and a few tenths with a large copper area on the drain leads. The real continuous current is a fraction of the printed one.

Twenty volts covers a single lithium cell, a 5 V rail, a 12 V rail with a clamp and a USB supply. It does not cover a 24 V rail, and on a 12 V rail the gate window of plus or minus 20 V leaves room that the 12 V sibling pair in this family does not have.

Key data for the VBK8238

ConfigurationSingle P channel
PackageSC70-6, six lead surface mount
VDSMinus 20 V
VGSPlus or minus 20 V
VthMinus 0.6 V typical
IDMinus 4 A, a die figure at a 25 C case
RDS(on) at 2.5 V45 milliohm
RDS(on) at 4.5 V34 milliohm
TechnologyTrench
Loss at 1 A0.034 W at 34 milliohm
Loss at 4 A0.54 W at 34 milliohm
Thermal pathSix small leads, no tab, the board is the heatsink

Where a low resistance in a small body helps

At 34 milliohm the conduction loss stops being the reason to reject the small body. A 1 A load loses 0.034 W, which is nothing. A 2 A load loses 0.14 W, which the leads pass with a decent pad. It is only when the load approaches the printed 4 A that the body becomes the limit, and at that point the problem is the solder joint and the copper rather than the silicon.

That shape of curve is useful for a load switch that has to pass a short inrush. The inrush current can be several amps for a few milliseconds while a capacitor bank charges, and the die handles that easily. The average loss is what heats the package, so a 4 A pulse at a 5 per cent duty cycle is a 0.027 W average and no problem at all.

The low threshold of minus 0.6 V is what makes a 2.5 V logic output enough to enhance the die. It also means the off state depends on the gate being held at the source, and a weak pull up on a warm board leaks through the channel. On a battery product that matters more than the resistance figure.

Twenty volts and the transients that come with it

A 20 V ceiling covers a 12 V rail at the 80 per cent rule to 16 V, which is inside a 12 V rail with a 10 per cent tolerance and not enough for an automotive 12 V rail that sees load dump. It covers a 5 V rail with a large margin and covers a single cell plus a boost to 15 V.

Where the rail is 12 V and there is a switching node nearby, the drain sees the rail plus the ringing, which can add several volts for a few nanoseconds. A transient suppressor or a snubber at the node keeps the peak inside the 20 V window. A 24 V rail is out of range whatever the clamp does.

The gate to source path is the other exposure. A fast rail transition through the gate to drain capacitance pulls the gate with it, and with a 0.6 V threshold a modest coupling is enough to turn the part partly on. A hard pull up and a short gate loop are the answer, and a small gate capacitor makes the coupling worse rather than better.

Where the part fits and where it does not

It fits a high side load switch on a 5 V or 12 V rail, a battery disconnect on a single cell product, a reverse polarity element on a USB input, a power multiplexer between two 5 V sources and an LED string switch. It does not fit a 24 V rail, and it does not fit a continuous load near 4 A in this body.

For a high side switch on a small rail the deciding parameters are the threshold, the resistance at the gate voltage available and what the body can remove. Our one stop BOM sourcing page covers how a group of small parts around a switch is bought on one order.

The sourcing side of this part is covered on the BOM scrubbing. For a small switch used in several places on one board, that page covers how the BOM is cleaned before the order.

Questions we get on this code

Does it really carry 4 A? The die does at a 25 C case. The package removes about 0.5 W at that current, which a six lead body in still air does not do without a large copper area.

What current should I plan for? 1 to 2 A continuous on a normal board, with pulses well above that, since the die handles inrush easily and the average loss is what heats it.

Can it be driven from a 3.3 V pin? Yes, through a level shifter or a pull down arrangement, since the gate has to go below the source. At 3.3 V rail the pin can pull the gate low directly.

What should a purchase order carry? Part number, SC70-6, and the packing the line can take. We confirm the reel quantity on the offer.