TPS3124J12DBVR
Product Specifications
TPS3124J12DBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS3124J12DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS3124J12DBVR 1.2 V processor supervisor with a high level reset and a watchdog
The TPS3124J12DBVR watches a 1.2 V rail and holds a processor in reset until that rail is above its threshold, then releases it after a fixed 180 ms delay. It also carries a watchdog timer that expects a pulse from the processor and pulls the reset line back if the pulse stops. Both jobs sit in a five pin SOT-23, which is the reason the part still appears on boards that were laid out years ago and on new ones that have very little room left.
The J in the order code is the part that matters most in this family. TPS3124 devices bring the reset out as a push-pull active high signal, which means the pin drives high when the rail is bad and low when it is good. The TPS3123 and TPS3126 members drive the opposite polarity and the TPS3125 and TPS3128 use an open drain output. A board that expects an active low reset will start up inverted with this part, so the suffix is not a decoration. The 12 in the string is the monitored rail, 1.2 V, and the threshold window that goes with it is 1.08 V to 1.12 V.
Key parameters taken from the TPS312x document
| Monitored rail | 1.2 V nominal, negative going threshold 1.08 V minimum and 1.12 V maximum |
| Minimum supply | 0.9 V, with the reset output defined above that level |
| Reset delay | 180 ms fixed, no external capacitor needed |
| Reset polarity | Push-pull active high, which is the J option on this family |
| Watchdog | Time-out 0.8 s minimum, 1.4 s typical, 2.1 s maximum, retriggered on a rising or a falling edge at WDI |
| Supply current | 14 microamp typical, which suits a rail that stays alive in a low power state |
| Manual reset | Not fitted. The TPS3123, TPS3125, TPS3126 and TPS3128 carry an MR pin, the TPS3124 does not |
| Hysteresis | Built into the comparator, so a rail that sits near the threshold does not chatter the reset line |
| Temperature | Minus 40 C to 85 C |
| Package | SOT-23-5, 3000 pieces on a large reel, moisture level 1, no floor life limit, marking PBQI |
| Lifecycle | The plain order code is active, the .A row of the same string is marked obsolete, so the string has to be ordered exactly |
The threshold window of 1.08 V to 1.12 V is worth reading twice. A 1.2 V rail at minus 5 per cent is 1.14 V, which is above the maximum threshold, so a supply that is inside its own tolerance still releases the reset. A rail at minus 8 per cent, 1.104 V, can sit inside the window and the outcome then depends on the individual part.
Where the numbers matter in a real build
The watchdog window is the first thing to plan. The timer runs from 0.8 s to 2.1 s across parts and temperature, so the software that feeds it has to send a pulse well inside the fast end. A service routine that toggles every 1.5 s will pass on a typical part and reset on a fast one, which is the kind of fault that only appears on a cold morning in the field.
The second point is the polarity. Because the output is push-pull and active high, it can drive a reset pin directly without a pull-up, but it cannot be wire-ORed with another reset source. A board with a debug header that also pulls the line low needs a series resistor or a different family member with an open drain output.
The third is the supply floor. The part monitors a 1.2 V rail while running from a supply that can fall to 0.9 V, and the output is only defined above that. Below 0.9 V the reset state is not guaranteed, so a board that relies on a defined level during a deep brown-out needs an external pull device.
What to check before a purchase order is released
- The output polarity against the processor reset pin, because the J option is active high.
- The watchdog period in the service routine, taken against the 0.8 s fast end and not against the 1.4 s typical.
- Whether the board needs a manual reset button, which this member does not support.
- The order string including the reel letter, since the .A row of the same code is obsolete.
- Whether any second reset source shares the line, which a push-pull output does not allow without a resistor.
- The 180 ms delay against the processor start-up time, because a rail that needs longer than that will start before it is ready.
Which projects this part fits
The vendor lists portable and battery powered equipment, wireless communication systems, industrial automation, servers and building automation. The pattern is a small processor on a low voltage core rail with no room for a supervisor plus a watchdog in two packages. A sensor node, a radio module or a small controller board with a 1.2 V core is the usual place this part appears.
Questions that come up before a purchase order is released
Is the reset delay adjustable?
No. The 180 ms delay is fixed inside the part, and the family has no delay capacitor pin. A board that needs a different delay needs a different device.
Does the watchdog run during reset?
The timer is cleared when reset is asserted, so the first window starts after the reset is released. That is what keeps a slow start-up from being cut short by the watchdog.
What happens if the rail sits exactly at the threshold?
The comparator has built in hysteresis, so the output does not chatter. The exact level at which it switches still depends on the part, which is why the window is printed as a range.
Can the part be used on a 1.5 V rail?
Not with this order code. The threshold is trimmed at the factory, so a 1.5 V rail needs the G15 member of the same family, with its own window of 1.40 V to 1.45 V.
How SUPERB handles this line
Small supervisors are the kind of part that goes obsolete first, because the package is old and the volumes are modest. Our pin to pin cross reference lists the checks a substitute has to pass before it goes on a released board, polarity included. Where the original string is no longer stocked, the obsolete part cross reference hub covers the alternatives, and our date code management explains how we handle a part that has been in a warehouse for years.