TPS544B25RVFR
Product Specifications
TPS544B25RVFR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS544B25RVFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS544B25RVFR 20 A PMBus converter with adaptive voltage scaling
The TPS544B25RVFR is the 20 A member of the TPS544x25 family, a PMBus 1.2 compliant synchronous step down converter that runs from 4.5 V to 18 V and delivers 0.5 V to 5.5 V out of a 5 mm by 7 mm LQFN package. The 30 A member, TPS544C25, shares the document and the pinout. The power stage is a stacked NexFET with 5.5 milliohm on the high side and 2.0 milliohm on the low side, and the current is sensed losslessly across the low side switch, so there is no shunt to buy and no shunt loss to pay for.
The PMBus interface is the reason this part exists in a server rather than a plain converter. Output voltage can be trimmed and margined over the bus, the reference spans 500 mV to 1500 mV for adaptive voltage scaling, and the part reports output voltage, output current and an optional external temperature. Fault response, whether the converter restarts, latches off or ignores the event, is a PMBus setting rather than a board change.
Adaptive voltage scaling matters at 20 A because a processor that can drop its own core voltage at low load saves more power than any efficiency tweak in the converter. The trimming resolution and the 0.5 per cent reference accuracy at 600 mV and above are what make that safe: a 600 mV rail trimmed by 10 mV is a 1.7 per cent move, and the loop has to know exactly where it started.
Key parameters from the SLUSC81 document
| Input range | 4.5 V to 18 V on the power stage, with an input turn on voltage programmable over 15 settings and 5 per cent accuracy |
| Output range | 0.5 V to 5.5 V, with a 500 mV to 1500 mV reference for adaptive voltage scaling and margining over PMBus |
| Output current | 20 A continuous for the B25 and 30 A for the C25 member, both from a 5.5 milliohm high side and 2.0 milliohm low side stage |
| Reference accuracy | 0.5 per cent at 600 mV and above between 0 and 85 degrees junction, widening to 0.8 per cent up to 1.5 V |
| Switching frequency | 500 kHz with a 40.2 k resistor on RT, specified as a window around that point, and synchronizable to an external clock |
| Soft start | 16 discrete ramp times selectable over PMBus with 10 per cent accuracy |
| Telemetry | Output voltage, output current and an optional external temperature channel read over PMBus 1.2 |
| Orderable body | LQFN-CLIP, 40 pins, 5 mm by 7 mm, 2500 pieces on a large reel and 250 on a small reel, RoHS exempt, minus 40 to 125 degrees |
What a PMBus converter changes for the board bring up
A converter with a bus can be configured after the board is built, which means a rail that comes up at the wrong voltage is a register value rather than a resistor change. It also means the board can be margined in software during a validation run instead of with a soldering iron. The cost is that the bus has to be reachable and the host has to have a driver, and a board that comes up before the host processor is awake needs the default settings in non volatile memory to be right.
The input turn on and turn off voltages are programmable over 15 settings, so a rail can be made to start only after the 12 V bus is above a chosen level, and the sequencing between rails can be coordinated over the bus rather than with a chain of enable resistors.
The current sensing is worth understanding
Low side current sensing measures the inductor current while the low side switch is on, so it sees the valley rather than the peak. The PMBus current reading is therefore a real output current with a known relation to the inductor ripple, and the overcurrent response is set on the same quantity. A board with a large ripple, low inductance and high frequency, reads lower than a board with a small ripple at the same average, which is why the current reporting has to be checked against a bench meter on the first build rather than trusted from the datasheet alone.
Where this part fits
Enterprise servers, switches and routers, storage arrays and telecom line cards use these converters for the core and memory rails, where the host wants to read current and trim voltage without extra hardware. The same part serves any board where a rail has to be margined in software during production test.
For a supply chain team the important question is that the PMBus configuration matches the board, because a converter programmed for another platform looks identical on the reel. The general method is set out in one stop BOM sourcing and in power management cross reference.
What to check before a purchase order
The first field is the current grade, 20 A for the B25 and 30 A for the C25, since the two share a document and often a listing. The second is the reel size, 2500 on the R row and 250 on the T row. The third is the RoHS exemption, which has to be declared on the customs paperwork in some markets and is not the same as a green declaration.
Our desk checks those three against the customer bill of materials and quotes the grade by current rather than by family name. See component lead time solutions when the grade is allocated.