Contact Us

TPS548A29RWWR

Brand: Texas Instruments
Texas Instruments TPS548A29RWWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS548A29RWWR — Power Management & Signal Chain | Superb Automation

TPS548A29RWWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS548A29RWWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS548A29RWWR 15 A buck with the 4.5 V LDO for 12 V and 5 V buses

The TPS548A29RWWR is the second member of the 15 A pair: 2.7 V to 16 V input, 15 A output, D-CAP3 control with no external compensation, a 0.6 V reference at 1 per cent and differential remote sense, all in the same 4 mm by 3 mm, 21 pin QFN. The difference from the A28 is the internal LDO, which is 4.5 V here instead of 3 V, and the FET resistances, which are 8.4 milliohm high side and 2.6 milliohm low side.

That LDO choice sets the applications apart. A 4.5 V LDO means the part runs at full 15 A from a 4.75 V to 5.3 V external bias, or from 4 V input without bias, and it does not try to work below 3 V on its own. For a board on a 12 V intermediate bus, or on a 5 V rail that never dips below 4.5 V, the 4.5 V LDO gives a stiffer gate drive and slightly better efficiency at heavy load than the 3 V version, because the FETs are driven harder.

Everything else is shared with the A28: the same pinout, the same MODE, TRIP, SS and REFIN pins, the same pin selectable 600 kHz, 800 kHz and 1 MHz frequencies, the same hiccup on overcurrent and undervoltage with latch off on overvoltage, and the same TRIP resistor scheme for a temperature compensated current limit.

Key parameters from the SLVSE78D document

Input range4 V to 16 V for 15 A without bias, 3 V to 16 V for 12 A without bias, 2.7 V to 16 V for 15 A with 4.75 V to 5.3 V external bias
Output range0.6 V to 5.5 V against a 0.6 V reference
Output current15 A continuous, 12 A in the 3 V to 4 V window without external bias
Power FETs8.4 milliohm high side and 2.6 milliohm low side, against 10.2 and 3.1 on the 3 V LDO version
Switching frequencyPin selectable 600 kHz, 800 kHz or 1 MHz
Reference accuracy0.6 V at 1 per cent over 40 to 125 degrees junction, differential remote sense
Current limitProgrammable with a resistor on TRIP, temperature compensated, hiccup on sustained overcurrent
Package21 pin QFN, 4 mm by 3 mm, pin compatible with the 12 A TPS54JA20 and with the A28

Choosing between the two LDO versions

If the input rail is 12 V and the board never sees below 4.75 V, the A29 gives lower conduction loss because the gate drive is higher and the FET resistances in the document are lower. If the input is a 5 V bus with a real brownout requirement, or a 3.3 V rail, the A28 is the part that keeps switching. The two share a footprint, so the decision can be deferred to the passive bill, but not to the VCC net: the A29 expects 4.75 V to 5.3 V on the bias pin and the A28 expects 3.13 V to 5.3 V, and a board that ties VCC to a 3.3 V rail only works with the A28.

Efficiency at 15 A from 12 V to 1 V is dominated by the low side conduction time, which is 92 per cent of the period. That is why 2.6 milliohm against 3.1 matters more than the high side figure, and why the A29 is the better choice in a 12 V to 1 V rack supply while the A28 is the better choice in a 5 V to 1.2 V point of load stage.

Reference input and tracking

REFIN lets the rail follow an external reference instead of the internal 0.6 V, which is how two rails are made to track during power up and power down. The feature is easy to get wrong: the divider has to be scaled to the external reference, not to 0.6 V, and a board built for a 0.6 V internal reference will sit at the wrong voltage if REFIN is driven and the divider was not recalculated. The document gives the transfer equation, and it is worth re deriving it on the bench before the first build.

Soft start is set by a capacitor on SS, and prebiased startup is supported. With the PGOOD output open drain, a supervisor or a sequencer can hold the next rail off until this one is in regulation.

Where this part fits

Data centre boards, FPGA and processor core rails, and 12 V to low voltage stages that need 15 A in a small footprint with no compensation network. The pin compatibility with the 12 A part and with the A28 makes it a good candidate for a family that is still settling its load current. See pin to pin cross reference and how to verify a drop in replacement for how we present the two versions side by side.

What to check before a purchase order

Two order codes differ by one character, A28 against A29, and the bodies look identical under a microscope. The marking code is the only reliable field on the reel, so a mixed carton is a real risk when a distributor splits a family. Confirm the bias arrangement on the board before shipping either version, and confirm the TRIP resistor, since a value chosen for the 3 V version trips at a different point on this one.

See date code management for how we segregate family members that share a carton, and component lead time solutions when one version is short and the other is not.

Questions that come up on this part

Can the A29 drop into a board built for the A28, is the usual question. Mechanically yes, electrically only if the VCC bias is at least 4.75 V. The second question is whether the higher LDO hurts light load efficiency. It does not, because the LDO current is nearly constant and the part enters Eco mode between pulses where the LDO draw is a small part of the total.