Contact Us

TPS546A24ARVFR

Brand: Texas Instruments
Texas Instruments TPS546A24ARVFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS546A24ARVFR — Power Management & Signal Chain | Superb Automation

TPS546A24ARVFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS546A24ARVFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS546A24ARVFR 10 A PMBus buck that stacks four deep for 40 A

The TPS546A24ARVFR is a 2.95 V to 18 V, 10 A synchronous buck in a 7 mm by 5 mm, 40 pin LQFN with 0.5 mm pitch. Two things put it in a different class from a pin strapped converter. The first is the PMBus interface at 1 MHz with telemetry for output voltage, output current and internal die temperature, plus AVS and margining. The second is the stack: two, three or four devices share current on one output and reach 40 A, and the back channel between them lets the whole stack answer to a single address, so the system controller sees one rail, not four.

The power stage is 5.5 milliohm high side and 1.8 milliohm low side, and the internal 5 V LDO can be overdriven from an external 5 V supply on VDD5, which is how a 12 V to 1 V rail at 10 A keeps its dissipation out of the package. Control is fixed frequency current mode with input feedforward and selectable internal compensation, so the loop stays stable across a wide range of output capacitance without an external network.

Twelve switching frequencies from 225 kHz to 1.5 MHz are selectable, eight of them by pin strap, which means a board can be built for one frequency and moved to another by resistor changes on the MSEL pins rather than by a PMBus write. Frequency sync in and out is available for systems that need to keep converters off each other's harmonics.

Key parameters from the SLUSE16A document

Input range2.95 V to 18 V on PVIN and AVIN, with 4 V minimum on VDD5 for switching
Output current10 A per device, 40 A with four devices stacked and sharing current on one address
Output voltage0.5 V to 5.5 V by pin strap, 0.25 V to 5.5 V through PMBus VOUT_COMMAND
Power FETs5.5 milliohm high side and 1.8 milliohm low side
Switching frequency12 settings from 225 kHz to 1.5 MHz, eight of them pin strapped, with sync in and sync out
Reference and accuracyDifferential remote sense with an internal feedback divider, under 1 per cent output error over 40 to 150 degrees junction
TelemetryVOUT, IOUT and internal die temperature over PMBus, with fault response set to restart, latch or ignore
Package40 pin LQFN, 7.00 mm by 5.00 mm by 1.5 mm, 0.5 mm pitch

Stacking without a second address

A four device stack of 10 A parts is how a 40 A core rail gets built with one part number and no current sharing controller. Each device senses its own output current, the back channel passes the error between them, and the group behaves as one converter with one set of PMBus commands. For the buyer this means a 40 A rail sits on four identical reels rather than on one high current module plus three satellites, which changes both the second source story and the repair story.

The pin strap defaults matter at production test. Because MSEL pins set the PMBus defaults, a board can power up correctly with no bus traffic at all, and the same board can be re characterised later by writing VOUT_COMMAND. A contract assembly line that has no PMBus master can therefore build and test the rail, and the end customer can still margin it in the rack.

Thermal and board consequences

At 10 A in a 7 by 5 mm body, the exposed pad is the whole thermal path. The document assumes a specific copper area under the pad and a number of vias into the ground plane, and a board that reduces either will not hold 10 A at 85 degrees ambient no matter what the current limit says. The VDD5 overdrive is the second lever: feeding 5 V from an external rail removes the LDO dissipation, which on a 12 V input is roughly 0.35 W at 10 A.

Input capacitance placement matters more than usual because 12 selectable frequencies include settings where the input ripple current lands near a system clock harmonic. Two 10 microfarad ceramics within a few millimetres of PVIN, plus the bulk bank, is the pattern the document uses. Sync in and sync out then let the whole rail group run from one clock so the beat note between converters does not appear on the input.

Where this part fits

Data centre switches and rack servers, active antenna systems, remote radio units and baseband units, automated test equipment, CT, PET and MRI scanners, and ASIC, SoC, FPGA and DSP core and I/O rails are named in the document. What they share is a rail that has to be margined and monitored rather than just powered, which is why the PMBus telemetry is the point of the part. For boards in this class we keep the cross reference and the drop in checks ready, see power management cross reference and how to verify a drop in replacement.

What to check before a purchase order

The suffix tells you the body: RVF is the 40 pin LQFN, and the same family string appears with other endings for other packages. The A in TPS546A24A is part of the order code and separates this device from the TPS546B24A, which shares the footprint but differs in the current rating and the pin strap table. A reel quoted for the wrong letter will fit the board and boot with the wrong defaults.

Second, confirm whether the line needs the PMBus master populated at test. Boards built for program free power up need the MSEL resistor values called out on the assembly drawing. See incoming inspection plan for how we check MSEL and address strap parts on receipt, and component lead time solutions when the 40 pin body is short.

Questions that come up on this part

Does stacking require matched devices from one lot, is the usual first question. No, the back channel handles the sharing, but all four must carry the same order code and the same pin strap, and mixing an A with a B in one stack is a fault waiting for a hot day. The second question is whether 1 MHz PMBus needs a specific pull up. It does, and the bus capacitance budget at 1 MHz is the number that decides whether the master can talk to four converters on one segment.