Contact Us

TPS552892RYQR

Brand: Texas Instruments
Texas Instruments TPS552892RYQR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS552892RYQR — Power Management & Signal Chain | Superb Automation

TPS552892RYQR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS552892RYQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS552892RYQR 36 V input, 8 A buck-boost for 60 W rails

The TPS552892RYQR is the 8 A member of the four switch buck-boost family: 3.0 V to 36 V input, 0.8 V to 22 V output, 1 per cent reference accuracy, in the same 3 mm by 5 mm HotRod QFN as the 4 A version. The power figures are 60 W from a 12 V input and 45 W from a 9 V input, with an 8 A average inductor current limit setting the ceiling, and peak efficiency of 96 per cent at 12 V to 20 V and 3 A.

The topology is what makes the part useful in a portable product: the output holds regulation while the input passes through it, so a 12 V rail stays at 12 V when a three cell pack falls to 9 V and rises again on charge. Average current mode control with a resistor set frequency from 200 kHz to 2.2 MHz, optional clock synchronization and optional spread spectrum cover the EMI side, and the output current monitor is 5 per cent accurate with adjustable cable droop compensation.

At 8 A the thermal path matters more than at 4 A. The body is the same, so the current density doubles and the copper under the pad becomes the deciding factor in whether the full 60 W is available at the ambient of the enclosure.

Key parameters from the SLVSH28A document

Input range3.0 V to 36 V, with 8 A average inductor current as the limiting figure
Output range0.8 V to 22 V programmable, 1 per cent reference accuracy
Power delivery60 W from 12 V input, 45 W from 9 V input
Efficiency96 per cent at 12 V to 20 V and 3 A
Switching frequency200 kHz to 2.2 MHz by resistor, clock sync, optional spread spectrum
Current monitoring5 per cent accurate output current monitor, adjustable cable droop compensation
Light loadProgrammable PFM and FPWM modes
ProtectionOutput overvoltage, average and cycle by cycle current limit, short circuit hiccup, thermal shutdown
Package3.0 mm by 5.0 mm HotRod QFN, RYQ body

60 W from a 3 by 5 mm body

The document's 60 W figure is at 12 V input, which is the point where the inductor current is lowest for a given output power in boost mode. At 9 V input the same part delivers 45 W, because the input current rises and the 8 A inductor limit is reached sooner. A product that quotes 60 W to a customer should state the input voltage it is quoted at, or the first field return will be a unit that folds back on a nearly empty battery.

Thermally, 60 W at 96 per cent leaves 2.5 W in the converter, and the 3 by 5 mm pad has to pass that into the board. The via array under the pad and the copper on the far side are the path, and a two layer board with a small pad copper will not hold the rating at 60 degrees ambient. Four layers with a solid ground plane under the part is the arrangement the figures assume.

Inductor and output capacitor choice

In boost mode the inductor carries the input current, and the 8 A limit means the inductor saturation rating has to be above that plus the ripple at the highest switching frequency deviation. A 1 microhenry part at 400 kHz with 30 per cent ripple sits near 10.4 A peak, so a 12 A saturation part is the sensible floor rather than the 8 A figure in the title.

The output bank has to hold the load through a mode transition, and in a buck-boost the transition happens while the input crosses the output, which is the worst case for the loop. The document gives the recommended ceramic values, and going below them shows up as an output dip at the crossing point rather than as a stability problem.

Where this part fits

USB PD adapters and power banks in the 45 W to 60 W class, automotive rails that must survive a crank, and instruments that run from a pack and from a 12 V adapter on the same input. See power management cross reference and component lead time solutions for how we handle the family when one rating is short.

What to check before a purchase order

The RYQ body is shared with the 4 A member, so the reel label is the only reliable difference. Confirm the inductor saturation and the thermal copper area before quoting a 60 W figure to an end customer, and confirm whether the board uses the I2C member of the family, which has a different order code and a different pin function on one pin.

See incoming inspection plan for the receipt check on leadless bodies, and one stop BOM sourcing for the whole power tree.

Questions that come up on this part

Can the 4 A and 8 A versions share a footprint, is the usual question. They can, the body is the same, and the passives decide which rating the board can actually deliver. The second question is whether spread spectrum is needed for a 60 W adapter. It depends on the emissions limit and on the enclosure; a metal case with a short input cable often passes without it, and a plastic case with a long cable often does not.