Contact Us

LM211QDRG4Q1

Brand: Texas Instruments
Texas Instruments LM211QDRG4Q1 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LM211QDRG4Q1 — Power Management & Signal Chain | Superb Automation

LM211QDRG4Q1

Texas Instruments — Power Management & Signal Chain

Product Overview

The LM211QDRG4Q1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LM211QDRG4Q1: what the Q1 and the G4 suffixes add to the LM211 die

LM211QDRG4Q1 is the single strobed comparator of the LM111, LM211 and LM311 family, ordered in the automotive temperature grade, on tape and reel, under the green material code. The die and the pinout are the ones the whole family shares. The four characters after the body code are the part a purchaser negotiates over, and none of them changes how the comparator switches.

The family has been in catalogues since 1973 and the document is still revised, which is a useful signal for a buyer: the part is not at the end of its life, four or five vendors build to the same pinout, and a threshold chain built on it can be re-sourced without a board change. That is why it keeps turning up in new builds even though faster comparators exist.

What follows is the layer of detail a distributor page leaves out: what each suffix decodes to, which rows change with the Q grade, what the strobe pin demands, and what to write on a purchase order so the reel that arrives is the reel that was quoted.

Decoding the string one field at a time

LM is the family prefix, 211 is the industrial input stage in the extended temperature grade, Q marks the wider guaranteed window, D is the eight pin small outline body, R is the tape and reel carrier, G4 is the green material code, and Q1 marks the automotive option that the data sheet lists under its Q-temp heading with configuration control, print support and qualification to automotive standards.

The base LM211 stops at plus 85 degrees. The Q grade extends the guaranteed window to plus 125 degrees, and the data sheet prints its own limits for that window instead of extrapolating the 25 degree numbers. That is the whole point of the grade: a limit guaranteed across the wider range is a different promise from a typical curve that happens to look flat.

Orderable codeLM211QDRG4Q1
Channels1, differential input, strobed
BodySOIC, 8 pins, 4.9 by 3.9 millimetres nominal
Carriertape and reel, 330 millimetre reel, 12.4 millimetre tape
Temperature windowminus 40 to plus 125 degrees, Q grade
Lead finishnickel palladium gold, green material code
Moisture levellevel 1, unlimited floor life at 260 degrees
Family documentSLCS007K, first issued September 1973, revised March 2017

The electrical rows that matter at 125 degrees

Offset voltage is the first row anyone reads. At 25 degrees the family is specified at 0.7 millivolts typical and 3 millivolts maximum, and the maximum widens to 4 millivolts over the full range. On the Q grade that 4 millivolt figure is the one that holds at the top of the window, so a threshold chain trimmed to 1 millivolt at room temperature still resolves, while a chain that spent the whole 3 millivolt budget at room temperature does not.

Input current is the second row and it matters more in high impedance work. Bias current is 75 nanoamps typical and 100 nanoamps maximum at 25 degrees, offset current is 4 nanoamps typical and 10 maximum, and both widen at the hot end, where junction leakage roughly doubles for every ten degrees. Across a 100 kilo ohm source the bias current produces 7.5 millivolts of drop at room temperature, which is already larger than the offset window, so a divider feeding the input has to be scaled against the bias current and not only against the ratio.

Input offset voltage at 25 degrees0.7 millivolts typical, 3 maximum
Input offset voltage over the full range4 millivolts maximum
Input offset current4 nanoamps typical, 10 maximum
Input bias current75 nanoamps typical, 100 maximum
Common mode range on plus or minus 15 voltsminus 14.5 to plus 13 volts
Large signal gain40 volts per millivolt minimum, 200 typical
Response time, low to high output115 nanoseconds typical
Response time, high to low output165 nanoseconds typical
Positive supply current, output low5.1 milliamps typical, 6 maximum
Output rating50 volts, 50 milliamps, collector and emitter brought out

Strobe and balance: two pins that punish an assumption

The strobe pin forces the output off regardless of the differential input, and the document is unusually direct about how to drive it. It needs a current of 3 to 5 milliamps, it must not be shorted to ground, and a resistor from a logic rail is the normal way to supply that current. From 5 volts, 1 kilo ohm gives 5 milliamps and 1.5 kilo ohm gives 3.3 milliamps, both inside the window. A 10 kilo ohm resistor gives half a milliamp and leaves the output in a state the data sheet does not promise.

The reason for the warning is the internal structure: the pin feeds a current mirror rather than a gate, so a hard short pulls an unbounded current through a small device. A board that drives the strobe from an open collector gate without a series resistor is a board that comes back from the field with a dead comparator, and the failure looks like a threshold fault rather than a drive fault.

The balance pins are the other half of the same story. A potentiometer between them with its wiper on the positive rail moves the offset through its window, and the trim is a production step set once at final test. On a mature product the potentiometer is usually replaced by two fixed resistors selected from a bin. Either way, the electrical rows assume the balance and strobe pins are open, so leaving them floating is allowed and tying them somewhere is not.

Driving a load that sits above the logic rail

The output is a floating transistor with both collector and emitter brought out, rated at 50 volts and 50 milliamps. That is what makes the part useful in a mixed voltage box: the collector can sit on a 24 volt rail while the input sits on a 5 volt rail, and the emitter output can drive a load referenced to the negative rail instead of ground.

Saturation voltage is 0.75 volts typical and 1.5 volts maximum at 50 milliamps, so a relay or an optocoupler driven straight from the collector sees about a volt of drop at full current. That is acceptable for a 12 volt relay with a 5 volt coil margin and it is not acceptable for a low headroom load, where a small signal MOSFET is the better switch. Leakage when the output is off is 0.2 nanoamps at 25 degrees and 0.5 microamps over temperature, which on a 100 kilo ohm pull up is 50 millivolts in the worst case. That leakage number is the one to compare against the input threshold of whatever reads the output.

What the green code and the reel change on the line

Nothing in the comparator changes between the tube body and the reel. What changes is the carrier and the handling: a 75 piece tube for prototypes, a 2000 piece reel on a 330 millimetre carrier for a line, the pocket 6.4 by 5.2 millimetres at 2.1 millimetres deep, and the green code with the nickel palladium gold finish and the level 1 moisture rating at 260 degrees peak reflow.

The level 1 rating is the practical difference for an assembler. A level 1 reel goes straight to the feeder with no bake step, and a line with no bake oven notices that immediately, while a line that already bakes every incoming reel will not. A partial reel is not returnable and a feeder setup is not free, so a build of ten prototypes wants the tube and a build of two thousand wants the reel even when the unit price is identical.

The orderable rows in this revision print LM211QD, LM211QDG4 and LM211QDR under the LM211Q device column at minus 40 to plus 125 degrees, with the reel row at 2000 pieces on the 330 millimetre carrier. The Q1 marker on the catalogue string is the automotive option described in the features list rather than a separately printed row in this addendum, so a programme that needs the automotive report should ask for the current automotive revision of the body before the purchase order is cut. Our power management cross reference page lists the family equivalents that share this pinout, and the date code management page covers how the reel date is recorded when the part is kitted into a build.

Buying questions that come with this code

Is the Q1 part a different die from the plain LM211? No. The Q marker is the extended temperature window and the Q1 marker is the automotive option, and the electrical rows for the window are printed in the same table.

Can it run from a single 5 volt rail? Yes. The offset, offset current and bias current rows apply from a single 5 volt supply up to plus or minus 15 volts, and the input common mode range reaches to within 1.5 volts of the positive rail. The response time and the offset window are the two rows to re-check in that configuration.

What replaces it if the reel is late? The LM311 in the same eight pin body, with a 0 to 70 degree window and the same pinout, or the LM211 in the plain industrial grade. Either move changes the temperature budget rather than the threshold, and our pin to pin cross reference page starts from the offset row rather than from the pinout for exactly that reason.