ISO7820FDWWR
Product Specifications
ISO7820FDWWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO7820FDWWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO7820FDWWR: a dual channel isolator with an 8000 VPK barrier
The ISO7820FDWWR is a two channel digital isolator with both channels forward, a low default and a barrier rated to 8000 VPK and 5700 VRMS. It is the highest isolation rating in the ISO78xx group, and the wide DWW body is what carries it. Where a product has to hold a barrier against a surge that a 5000 VRMS part would not survive, this is the row that gets specified.
Data rate is 100 Mbps, propagation delay is 11 ns typical and 17.5 ns maximum at 5 V, and the input common mode transient immunity is 100 kV per microsecond minimum rather than typical, which is unusual and useful in a high dv/dt cabinet. Supply current is 1.7 mA per channel typical at 1 Mbps, and the part runs from 2.25 V to 5.5 V on each side with translation across the barrier.
The F letter sets the default low when input power or the input signal is lost. The plain member of the same die holds the outputs high. Two channels in this body cover an isolated serial pair, a gate command and its enable, or a clock and a data line into a high voltage stage.
Key data for the ISO7820FDWWR
| Channels | Two, both forward, with no reverse channel on this member |
| Data rate | 100 Mbps maximum specified |
| Isolation | 5700 VRMS and 8000 VPK, the highest rating in the ISO78xx group |
| Supply | 2.25 V to 5.5 V on each side, level translation across the barrier |
| Timing | Propagation delay 11 ns typical and 17.5 ns maximum at 5 V, pulse width distortion 2.5 ns maximum |
| Immunity | CMTI 100 kV per microsecond minimum, quoted as a limit rather than a typical |
| Default state | Output low on loss of input power or signal, the F variant |
Body, packing and marking data
| Body | SOIC DWW, 16 pins, the extra wide outline that the 8000 VPK barrier needs |
| Packing | 1000 pieces on a large reel on the plain and the A row |
| Finish | NIPDAU, moisture level 3 with a 168 hour floor life, 260 C peak |
| Marking | 7820F printed on the body |
| Temperature | Minus 55 C to plus 125 C |
Moisture level 3 is the handling detail that bites
This body is moisture level 3 with a 168 hour floor life, while most of the family sits at level 2 with a full year. That difference matters on a line that opens a reel on Monday and finishes it on Friday. A level 3 part that has been out of the bag for more than 168 hours at 30 C and 60 per cent relative humidity needs a bake before reflow, or the package will delaminate and the barrier will fail a hi pot test later.
The practical control is a floor life label on the reel and a clock that starts when the bag is opened. For a low volume line, the bake is cheaper than the tracking. For a high volume line, the tracking pays for itself in one avoided recall. Whichever route is used, the record has to travel with the lot, because a barrier part that has absorbed moisture looks and measures exactly like a good one until the reflow.
Where an 8000 VPK barrier earns its cost
Grid equipment, protection relays and traction hardware see surges that a basic barrier does not survive, and the 5700 VRMS rating with an 8000 VPK impulse rating is chosen for those events rather than for steady state stress. The same rating is used in defence and aerospace hardware where the isolation has to hold through an induced transient, and our defense grade components page covers the documentation those programmes ask for.
Medical equipment also uses this family where the applied voltage is high enough that a 5000 VRMS part leaves too little margin. The certificate names the working voltage, and the medical device component sourcing page sets out how that number is checked against the application.
Questions we get on this code
Buyers ask for the difference between this part and the 5000 VRMS members of the same family. The answer is the body and the certificate, not the die speed. Both run at 100 Mbps and both translate across 2.25 V to 5.5 V, so the choice is made on the barrier rating and the board space, and the wider body costs area.
The second question is whether the 1000 piece reel can be split. It can, but every split resets the moisture clock, so a partial reel has to be resealed with a desiccant and a fresh label. A broker who splits a reel without resealing is handing over a part that has already spent its floor life in the open air, and no amount of visual inspection will show it.