INA225AIDGKR
Product Specifications
INA225AIDGKR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA225AIDGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA225AIDGKR: 36 V programmable gain current shunt monitor with an external reference
INA225AIDGKR is a bidirectional current sense amplifier whose gain is chosen by two logic pins in a VSSOP body of 8 pins. It senses a shunt drop from 0 V to 36 V of common mode and scales it by 25, 50, 100 or 200 through the GS0 and GS1 pins, so one part covers four current ranges on a single board. The REF pin takes an external reference, which is what makes a bidirectional measurement possible without a negative supply, and the whole device draws 350 uA at most.
Order code and package
| INA225AIDGKR | VSSOP DGK body, 8 pins, 2500 pieces on a large reel, Active, part marking B32, nickel palladium gold lead finish, moisture level 2 with a one year floor life |
| INA225AIDGKR.A | the same body and the same 2500 piece reel, printed as a second row of the same addendum |
| INA225AIDGK | the tube form of the same body, used for hand assembly and for evaluation |
| Body size | 3.0 mm by 3.0 mm, the same footprint as the eight pin VSSOP used across this family |
Electrical parameters that decide the application
| Common mode range | 0 V to 36 V, independent of the supply, with no negative common mode window |
| Supply | 2.7 V to 36 V, 350 uA maximum supply current across the full temperature range |
| Programmable gains | 25 V/V with both select pins low, 50 V/V with GS0 low and GS1 high, 100 V/V with GS0 high and GS1 low, 200 V/V with both high |
| Offset voltage | plus or minus 150 uV maximum at every gain, drift 0.5 uV per degree maximum |
| Gain accuracy over temperature | plus or minus 0.15 per cent at 25 and 50 V/V, 0.2 per cent at 100 V/V, 0.3 per cent at 200 V/V |
| Gain drift | 10 ppm per degree maximum |
| Bandwidth | 250 kHz at a gain of 25 V/V |
| Output stage | voltage output referred to the REF pin, so the zero current point can be moved away from ground |
| Temperature range | minus 40 to plus 125 degrees ambient |
Family variants and how they differ
| Gain 25 V/V | the widest current range, used when the shunt drop reaches tens of millivolts and the converter needs the full span |
| Gain 50 V/V | the middle setting for a 5 V converter and a 20 mV full scale drop |
| Gain 100 V/V | for a 10 mV full scale drop, the smallest the family claims full accuracy on |
| Gain 200 V/V | the last setting, with the loosest gain accuracy of the four at 0.3 per cent |
| Select pins | GS0 and GS1 are read continuously, so the gain can be changed during operation if the converter can tolerate the settling time |
Points to check before this part goes on a BOM
The select pins are static logic, not a register. Each pin is tied to GND or to VS on the board, so the gain is fixed by the hardware unless a controller drives the two pins itself, and the four settings are read from the same die rather than from four order codes.
The REF pin is what separates this part from a fixed gain monitor. A reference at half the converter span puts zero current in the middle of the output range, which is how a battery that charges and discharges reports both directions on a single positive supply.
The common mode window starts at 0 V rather than below it. That is enough for a low side shunt referenced to ground and for a high side shunt on a positive rail, but a rail that swings below ground has to be handled with a different member of the family.
Gain accuracy is not the same at all four settings. The 25 and 50 V/V rows are specified at 0.15 per cent, the 100 V/V row at 0.2 per cent and the 200 V/V row at 0.3 per cent, so a board that needs tight accuracy at the highest gain has to accept the wider window or move to a fixed gain part with a tighter specification.
The 250 kHz bandwidth figure belongs to the lowest gain setting. At 200 V/V the closed loop bandwidth is lower, and the document does not print a row for each gain, so a control loop that depends on the small signal response should be checked on the bench rather than inferred from the 25 V/V number.
One part number, four current ranges
A board that has to cover a 2 A standby current and a 40 A peak on the same shunt can use one order code and two settings, and a firmware change moves the range without a rework. The alternative, four fixed gain parts, means four order codes on the bill of materials, four places in the incoming inspection sheet and four chances of a wrong part reaching the line, and on a small board the select pins cost less than the extra part numbers do.
The price of that flexibility is the gain error at the top setting and the extra two traces to the select pins. On a board with a fixed current range those two arguments are usually enough to choose a fixed gain part instead, which is why this device sits in the middle of the family rather than at the low cost end.
Why the supply range reaches 36 V
A 36 V supply window lets the part sit on the same rail it is measuring, which removes a low dropout regulator from a small board. On a 24 V industrial rail that is a real saving, and it also means the amplifier supply collapses with the rail, so the reading disappears exactly when the rail sags rather than reporting a false zero from a still powered device.
The common mode window and the supply window are separate numbers even though both reach 36 V on this part. A 36 V common mode can be sensed from a 5 V supply, which is the arrangement used when the logic rail is already regulated and only the sense point is high.
Reading the reference pin correctly
The output is referenced to REF, so the zero current level follows whatever is applied to that pin. If REF is left floating or tied to a rail that is not the same one the converter uses, the offset appears as a fixed current error that no calibration of the shunt will remove. Tying REF to the same reference the ADC uses is the arrangement that keeps the zero point stable over temperature.
Where this order code fits
Power supplies, motor control, computers, telecom equipment, power management and test and measurement are the applications the vendor names, and each of them wants one current signal per rail with a range that can be changed without a new board. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
How is the gain set? By the two select pins: both low is 25 V/V, GS0 low with GS1 high is 50 V/V, GS0 high with GS1 low is 100 V/V and both high is 200 V/V. The pins are read continuously, so a controller can change the range while the rail is live.
Can it sense below ground? No. The common mode window starts at 0 V, so a rail that swings negative needs a different device.
Is the output bidirectional? Yes, by moving the REF pin away from ground, which places zero current inside the output range.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.