Contact Us

TPS62143RGTR

Brand: Texas Instruments
Texas Instruments TPS62143RGTR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62143RGTR — Power Management & Signal Chain | Superb Automation

TPS62143RGTR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62143RGTR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62143RGTR: 3 V to 17 V input, 2 A step-down, fixed 5.0 V output, 2.5 MHz, VQFN-16

TPS62143RGTR is a synchronous step-down converter rated 2 A with a fixed 5.0 V output, a 2.5 MHz switching frequency and an open drain power good output in a VQFN body of 16 pins. The fixed 5.0 V version removes the feedback divider and the divider error entirely, which is why it appears on boards that need a clean 5 V rail from a 12 V bus. The 2.5 MHz switching frequency keeps the inductor small, and the DCS-Control loop stays in regulation through load steps without an external compensation network.

Order code and package

TPS62143RGTRActive, VQFN-16, 3000 pieces on a large reel, NIPDAU finish, MSL-1-260C unlimited floor life, marking QWC
TPS62143RGTRG4Active, the same body and reel with the Green material declaration
TPS62141 and TPS62142the 1.8 V and 3.3 V fixed members of the same family, same body and pinout
TPS62140 and TPS62140Athe adjustable members, which need an external divider
Package size3 mm by 3 mm, sixteen pins, exposed pad on the underside

Electrical parameters that decide the application

Input voltage3 V to 17 V
Output5.0 V fixed on this string, 2 A continuous
Switching frequency2.5 MHz typical, selectable to a lower value through the FSW pin
Quiescent current17 microamp typical in power save
Shutdown currentless than 2 microamp
Duty cycle100 per cent mode, so the output follows the input at low headroom
Power goodopen drain, high impedance when the enable pin is low
Operating rangeminus 40 to 125 degrees junction

Family variants and how they differ

TPS62143fixed 5.0 V, high impedance power good when disabled, the string on this page
TPS62141fixed 1.8 V, otherwise identical
TPS62142fixed 3.3 V, otherwise identical
TPS62140Aadjustable, with a power good that pulls low when the enable pin is low
DEF pinpulls the output up by 5 per cent when it is driven high, so a nominal or a raised rail can be selected at run time

Points to check before this part goes on a BOM

The DEF pin changes the output by five per cent. On the fixed voltage members, pulling DEF high raises the regulated output by 5 per cent, so a 5.0 V rail becomes 5.25 V. That is useful for compensating a cable drop or for testing margin on a load, and it is a trap on a board where the pin floats or is driven by a signal that was not intended. The pin has an internal state, but relying on it without checking is how a 5.25 V rail appears on a board that was specified at 5.0 V.

A fixed output removes the divider and its error. The 5.0 V is set inside the package against the internal reference, so there is no divider tolerance, no divider drift and no leakage path from the output to ground when the converter is off. On a rail that has to be accurate, the fixed member is the better choice even though the adjustable one costs the same.

Two and a half megahertz is high and it buys board area. At 2.5 MHz the inductor is under a microhenry and the output capacitor is a small ceramic, so the whole converter fits in a few square millimetres. The cost is switching loss, which is why the efficiency at 12 V in and 5 V out is good but not the best in class, and why the FSW pin exists to drop the frequency when efficiency matters more than size.

One hundred per cent duty cycle is the low headroom mode. When the input falls close to 5 V the high side switch stays on and the output follows the input minus the resistive drop. A 5.0 V rail from a 5.2 V input will not be regulated, but it will stay alive, which is what a battery powered product needs at the end of discharge.

The power good logic level depends on the family member. On this string the output is high impedance when the enable pin is low. On the TPS62140A it pulls low. A board that relies on power good being low during shutdown behaves differently depending on which member is fitted, and a substitution across the family changes the sequencing logic.

Soft start is set by the SS pin, not fixed. A capacitor on the SS pin sets the ramp, and the same pin can be used to track another rail. That is how two converters are made to come up together, with one following the other rather than each starting on its own enable.

The VQFN exposed pad is the thermal path and the ground. All the heat leaves through the pad, and the pad is also the power ground. A pad with a few vias into a ground plane is enough for 2 A at 12 V in; a pad connected by a single trace is not, and the part will thermal cycle in a way that looks like an unstable loop.

Seventeen volts is the ceiling and a 12 V bus is comfortable. A 12 V rail with ten per cent tolerance reaches 13.2 V. A 15 V rail is also inside. A 19 V adapter is above the rating and needs a different part, which is the same trap as with the smaller converters in this band.

It is pin compatible with two other families, which is why repair stock is easy. The body is pin to pin compatible with the TPS62130 and TPS62150 families, so a board built around one of those can take this part when the original is unavailable. The fixed output has to be checked against the board divider, because a fixed member in a socket that expects an adjustable one will ignore the divider and produce the internal voltage.

What to confirm before this part goes on a purchase order

Confirm whether the board expects a fixed 5.0 V member or an adjustable one. The bodies are identical and the pinout is shared, and fitting the wrong member leaves the divider connected to a pin that ignores it.

Ask for the date code, the marking QWC and the country of origin. Because three families are pin compatible in this body, the marking is the only reliable field on a mixed shelf.

Where this order code fits

It makes a fixed 5.0 V rail at 2 A from a 12 V bus in a solid state drive, an embedded controller or an ePOS terminal, and reports power good before the next rail starts. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Does it need an external divider? No, the 5.0 V is fixed inside the package. That is the reason to choose this member: no divider error, no divider leakage and two fewer parts on the board.

What does the DEF pin do? Pulling it high raises the output by 5 per cent, so 5.0 V becomes 5.25 V. It is useful for margin testing and for compensating a cable drop, and it has to be tied to a defined level on a production board.

Can it run at 12 V in with a 5 V output at 2 A? Yes, that is the intended application. The dissipation is modest at that ratio and the 3 mm package handles it with the exposed pad soldered to a ground plane.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.