TPS560430XDBVR
Product Specifications
TPS560430XDBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS560430XDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS560430XDBVR: 600 mA synchronous buck, 4 V to 36 V input, 1.1 MHz pulse frequency version
TPS560430XDBVR is a 600 mA synchronous step-down converter with a 36 V input rating in a SOT-23 body of 6 pins. The X letter marks the 1.1 MHz pulse frequency version, so this part skips pulses at light load and keeps efficiency up where the load is small. Soft start and compensation are internal, the reference is 0.8 V with 1.5 per cent tolerance over temperature, and the whole converter fits in a six pin SOT-23 with no external network beyond the inductor and the capacitors.
Order code and package
| TPS560430XDBVR | Active, SOT-23-6, minus 40 to 125 degrees, marking NAXS |
| Reel caution | the addendum prints the R row at 250 pieces on a small reel and the T row at 3000 on a large reel, which is the reverse of the usual convention |
| TPS560430XFDBVR | 1.1 MHz forced PWM, adjustable output |
| TPS560430X3FDBVR | 1.1 MHz forced PWM, fixed 3.3 V output |
| TPS560430YDBVR | 2.1 MHz pulse frequency, adjustable output |
Electrical parameters that decide the application
| Input voltage | 4 V to 36 V |
| Continuous current | 600 mA |
| Output voltage | adjustable through a divider, or fixed 3.3 V on the X3F member |
| Switching frequency | 1.1 MHz on the X members, 2.1 MHz on the Y members |
| Reference | 0.8 V, plus or minus 1.5 per cent over temperature |
| Minimum on time | 60 nanosecond |
| Maximum duty cycle | 98 per cent |
| Protection | cycle by cycle current limit, hiccup on short circuit, thermal shutdown |
Family variants and how they differ
| X | 1.1 MHz, pulse frequency modulation, adjustable output, this order code |
| XF | 1.1 MHz, forced PWM, adjustable output |
| X3F | 1.1 MHz, forced PWM, fixed 3.3 V output |
| Y | 2.1 MHz, pulse frequency modulation, adjustable output |
| YF | 2.1 MHz, forced PWM, adjustable output |
Points to check before this part goes on a BOM
The X and Y letters change the inductor, not only the frequency. At 2.1 MHz the same current needs roughly half the inductance and gives a smaller solution with more switching loss. At 1.1 MHz the inductor is larger and the efficiency is better. A board that was laid out for the 2.1 MHz member and substituted to the 1.1 MHz one keeps a small inductor that is now too small for the ripple target.
Pulse frequency modulation is the reason the quiescent current is low. The part skips pulses at light load, which keeps the no load input current small. The forced PWM members never skip, so they hold a constant frequency and a lower ripple at the cost of no load current. On a 24 V sensor that wakes twice a day, the PFM member is the one that keeps the average current inside the budget.
The reel rows in the addendum look swapped. This document prints the R suffix at 250 pieces on a small reel and the T suffix at 3000 on a large reel, which is the opposite of the convention used elsewhere in the same family. The suffix cannot be trusted to imply the packing here, so the reel size has to be confirmed on the offer or from the label.
36 V input is what separates this part from the 17 V converters. A 24 V industrial bus with a transient to 30 V is comfortable here and impossible on a 17 V part. The 600 mA rating is modest, and it is the reason the part survives in a six pin body at that input voltage: the current, not the voltage, sets the dissipation.
60 nanosecond minimum on time sets the maximum step down ratio. At 1.1 MHz a 60 nanosecond pulse is about 6.6 per cent of the period, so a 36 V input cannot produce much below 2.4 V without skipping pulses. A 24 V to 1.2 V rail is outside what this part can regulate continuously, and the frequency choice makes that worse.
98 per cent duty cycle is a pass through, not a regulator. At the top of the range the output follows the input and the loop is out of regulation. That is useful when a 24 V bus sags to 20 V and the rail is set at 19 V, and it is not useful as a way to hold a precise output near the input.
Hiccup on a short is the behaviour a safety reviewer looks for. The current limit acts cycle by cycle, and a sustained short puts the part into hiccup so the average current stays low instead of cooking the inductor. The recovery is automatic, which is what a sealed unit needs, since a latched converter in a box cannot be reset.
The fixed 3.3 V member removes the divider and its error. X3F gives 3.3 V with no external resistors, which saves two parts and removes the divider tolerance from the output. On a 3.3 V rail that is the cheapest accuracy in the whole circuit, and it is a different order code rather than a different resistor value.
The six pin body has no power good, and that changes sequencing. A rail that has to start before another one uses the enable pin of the second converter with a divider from this output, which is a comparator rather than a flag. On a two rail board that is one extra part, and it is the reason slightly larger members with a power good pin exist in other families.
Efficiency at full load is set by the inductor as much as by the part. A small inductor with high direct current resistance costs more in copper loss than the converter gains in switching loss, and the difference appears at 600 mA rather than at idle. The inductor is the component to spend money on in this class of converter.
The fixed 3.3 V member is a separate line on the addendum. It carries its own orderable string and its own packing rows, so a shortage of the adjustable member does not mean the fixed one is available, even though the silicon behind both is the same.
Where a 36 V input, 600 mA converter earns its place
24 V industrial sensors and actuators that need a local 5 V or 3.3 V rail, where the current is small and the input is the hostile part of the problem.
12 V and 24 V battery backed equipment that has to keep a logic rail alive while the main load is switched off.
Where this order code fits
It makes 600 mA rails from 24 V industrial buses and 12 V supplies, where the input range and the six pin body are the reason for choosing it. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Can it deliver 600 mA from 24 V to 3.3 V continuously? Electrically yes. The dissipation at 600 mA is small because the switch is integrated and the current is modest, so the SOT-23-6 handles it on a normal copper area. The limit is the 60 nanosecond minimum on time, which is comfortable at a 24 V to 3.3 V ratio.
What is the difference between the X and Y versions? The switching frequency, 1.1 MHz against 2.1 MHz. That changes the inductor value, the switching loss and the size of the solution. The pinout and the current rating are the same.
Does the output need a divider? On this member yes, the output is adjustable. The X3F member is the fixed 3.3 V version and needs no resistors. Both are six pin SOT-23 parts, so the difference is the order code and two components.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.