Contact Us

TPS61390RTER

Brand: Texas Instruments
Texas Instruments TPS61390RTER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS61390RTER — Power Management & Signal Chain | Superb Automation

TPS61390RTER

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS61390RTER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS61390RTER: 700 kHz boost converter with an 85 V switch for avalanche photodiode bias

TPS61390RTER is a step-up converter with an 85 V switch and a sampled current mirror for photodiode bias in a WQFN body of 16 pins. It raises 2.5 V to 5.5 V up to 85 V with a 1000 mA switch current limit, and it carries a current mirror with two selectable gains plus a sample and hold stage, so the photodiode current can be measured by an external converter without a second amplifier chain. The optical power protection responds in 0.5 microsecond, which is the figure that protects the diode rather than the board.

Order code and package

TPS61390RTERActive, WQFN-16, 3000 pieces on a large reel, SN finish, MSL-1-260C-UNLIM, minus 40 to 125 degrees
TPS61390RTETActive, the same body, 250 pieces on a small reel
Marking1XQH on the RTE body
Body3 mm by 3 mm by 0.75 mm QFN with the thermal pad
Current limit programminga resistor sets the optical power protection threshold

Electrical parameters that decide the application

Input voltage2.5 V to 5.5 V
Output voltageup to 85 V
Switch on resistance0.9 ohm
Switch current limit1000 mA
Switching frequency700 kHz
Quiescent current110 microamp from the input, 340 from the output, 140 from the analog rail
Soft start4.8 millisecond
Sample window400 nanosecond minimum

Family variants and how they differ

Current mirror gain 1 to 5selected by the GAIN pin held low, used for the higher optical input range
Current mirror gain 4 to 5selected by the GAIN pin held high, a larger fraction of the diode current
Sample and holdcaptures the mirror output for an external converter to read
Optical power protectionan additional FET in series with the diode, 0.5 microsecond response
Thermal resistance52.9 degrees per watt junction to ambient

Points to check before this part goes on a BOM

The current mirror is the reason this part exists. Measuring an avalanche photodiode current normally needs a transimpedance stage and a careful bias network. The mirror brings a scaled copy of the diode current out of the converter, and the sample and hold stage lets a slow external converter read it without loading the bias node. That removes parts and removes the stability problem of an amplifier sitting on an 80 V rail.

Two gains are there because the optical range spans decades. At 1 to 5 the mirror divides the diode current by five, so a large signal stays inside the input range of an ordinary converter. At 4 to 5 it passes almost all of it, which is what a weak signal needs. The pin that selects the gain also changes what the sample and hold output means, so the firmware has to know which state it set.

0.5 microsecond protection is a diode figure, not a converter figure. An avalanche photodiode can be damaged by an overcurrent well before a normal current limit loop reacts. The separate protection FET and its dedicated sense path are what makes the response fast enough, and the threshold is set by a resistor, which makes it a component choice rather than a fixed limit.

85 V output with a 0.9 ohm switch means the switch is not the limit. The duty cycle and the diode reverse recovery are what set the achievable output at a given current. At an 85 V output the switch conducts for a short part of the period and the inductor current ramps in a narrow window, so the peak current limit is reached at a lower average input current than the 1000 mA figure suggests.

Three quiescent currents are quoted and all three matter. The input, output and analog rail each have their own figure. A bias converter that runs continuously in an optical module is part of the module power budget, and quoting only the input figure understates the total. The output rail figure is the one that continues to draw while the switching stage is idle.

The soft start of 4.8 millisecond is fixed. On an 85 V output the ramp has to be slow enough that the output capacitor is not charged faster than the switch current limit allows. A faster ramp would simply sit in current limit, which is the same result with more stress. There is nothing to tune here, and a board that needs a slower ramp needs a different arrangement.

400 nanosecond sample window is the speed of the measurement. A receiver that switches between strong and weak optical input needs the bias current to be captured quickly, otherwise the reading belongs to the previous state. The window is the specification to compare against the burst rate of the system, not against the converter sample rate.

WQFN with a thermal pad on a 3 mm body. 52.9 degrees per watt is a reasonable figure only when the pad is soldered to copper. A 85 V output at a few milliamp is a small dissipation, so the thermal problem is not the hard part of this circuit, and the high voltage clearance around the switch node and the diode is.

The diode and the inductor are rated for the output, not the input. A 100 V diode is the minimum at an 85 V output and a 150 V part is normal once the switch node ringing is counted. The inductor saturation current has to cover the 1000 mA switch limit rather than the average output current, because the converter reaches that limit on start up and during a fast bias change.

The bias converter runs continuously in an optical module. The 110 microamp from the input plus 340 from the output is a permanent load on the module supply, and in a receiver fed from a line card that budget matters. Switching the bias converter off between bursts saves the current and pays a settling time on every burst.

The 700 kHz frequency is a compromise, not a target. Higher would shrink the inductor and raise the switching loss on an 85 V node, where the capacitive losses are significant. Lower would need a larger inductor and slow the bias settling. The fixed point sits where both are tolerable.

What the bias circuit has to get right

The inductor and the diode have to be rated for the full output voltage plus margin, not for the input. At 85 V output a 100 V diode is the minimum and a 150 V part is the usual choice.

The protection threshold resistor sets the current at which the series FET opens, and that value belongs to the photodiode rating rather than to the converter.

Where this order code fits

It biases an avalanche photodiode in an optical receiver, and any other rail that needs up to 85 V at low current with a monitored return. Teams comparing it with a neighbouring part start from our RF Component Sourcing page, and teams replacing a part that has gone end of life start from the Power Management Cross Reference page.

Questions buyers ask

Can it generate 85 V from a 3.3 V rail? Yes, that is the intended application. The switch is rated for 85 V and the duty cycle needed from 3.3 V is high, so the inductor and the diode have to be chosen for that operating point rather than for a lower output.

What does the sample and hold output give? A scaled copy of the photodiode current, held for an external converter to read. The scale is set by the GAIN pin, 1 to 5 or 4 to 5, and the held value is only valid after the 400 nanosecond sample window has elapsed.

Is the optical protection adjustable? Yes, a resistor sets the threshold. The protection is a separate FET in series with the diode with a 0.5 microsecond response, so it acts faster than the converter current limit loop.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Obsolete RF Part Replacement page sets out the checks that keep a substitute from failing on the bench.