Contact Us

TPS7A2601DRVR

Brand: Texas Instruments
Texas Instruments TPS7A2601DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A2601DRVR — Power Management & Signal Chain | Superb Automation

TPS7A2601DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A2601DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A2601DRVR: 500 mA, 18 V, 2 microamp LDO with power good, adjustable output

TPS7A2601DRVR is a 500 mA linear regulator with a 2 microamp quiescent current and a power good output in a WSON body of 6 pins. It is the 500 mA member of the TPS7A2x pair: the same 18 V input and 2 microamp quiescent current as the 200 mA part, with a 590 mV maximum dropout at full load and an open drain power good. The adjustable version sets the output from 1.24 V to 17.4 V through a divider, and the fixed members cover 1.25 V to 5.5 V with no external resistors.

Order code and package

TPS7A2601DRVRActive, WSON-6, 3000 pieces on a large reel, NIPDAU finish, MSL-1, minus 40 to 125 degrees
TPS7A2601DRVTActive, the same body, 250 pieces on a small reel
Fixed members1.25 V to 5.5 V in the same body, no divider needed
Marking7A26 on the DRV body
SiblingTPS7A24, 200 mA with a 250 mV dropout, no power good

Electrical parameters that decide the application

Input voltage2.4 V to 18 V
Output current500 mA
Output range1.24 V to 17.4 V adjustable on this string
Quiescent current2.0 microamp
Dropout590 mV maximum at 500 mA
Accuracy1 per cent over temperature
Power goodopen drain output
Output capacitorstable with 1 microfarad

Family variants and how they differ

TPS7A24200 mA, 250 mV dropout, no power good, same input range
TPS7A26500 mA, 590 mV dropout, power good, this family
Fixed versionno divider, no divider error, two fewer components
Overshoot pulldownactive discharge when the input collapses
Bodysix pin WSON, 2 mm by 2 mm class

Points to check before this part goes on a BOM

590 mV at 500 mA against 250 mV at 200 mA is the whole difference between the two parts. The larger current needs a larger pass device, and the dropout rises with it. A rail that has 400 mV of headroom works with the 200 mA part and does not work with this one at full load. The current and the headroom have to be chosen together.

2 microamp with 500 mA available is the unusual combination. Most 500 mA regulators draw tens of microamp because the bias circuit is sized for the full load. This one keeps the nanopower bias and pays for it with a higher dropout. It is the right part for a load that is mostly asleep and occasionally draws half an amp, which describes a radio module or a motor driver in standby.

The power good output removes a comparator from the board. It reports when the output is in regulation, so a downstream rail or a processor can wait for it instead of using a fixed delay. The pin is open drain, so the pull up decides the logic level and the rise time, and a large pull up with a long trace gives a slow edge that some inputs do not like.

1 per cent over temperature is tighter than the 200 mA sibling. For a 3.3 V rail that is 33 mV across the range. It is still not a reference, but it is tight enough for a rail that feeds a microcontroller and its analogue front end on the same supply, which is why the part is often used as the last regulator in a chain.

The adjustable version needs a divider that does not waste the quiescent current. At 2 microamp, a divider in the tens of microamp defeats the purpose of the part. The values have to be large, in the hundreds of kilohm, and at that point the leakage into the feedback pin and the board contamination become part of the error budget. On a 1 per cent part that matters.

18 V input with a 500 mA load is 9 W of dissipation at the top of the range. No six pin body takes that. The part is intended for a wide input with a modest average current, where the high input only occurs in a transient. A customer asking for 500 mA continuously from 12 V to 3.3 V needs a switching converter, and the honest answer is to say so.

The active overshoot pulldown protects the load during a fast input collapse. When the input falls quickly the output can be left above it, with the charge stored in the output capacitor. The pulldown discharges it, which keeps a processor from seeing a reverse biased rail. It does not replace a reverse blocking diode where the load itself can source current.

Six pin WSON with a thermal pad is a board decision. The pad has to be soldered to a copper area to pass the dissipation, and it also carries ground. A footprint drawn for a five pin SOT-23 will not accept this part, so a substitution between the bodies is a board change rather than a purchasing decision.

Power good on a linear regulator is a slow signal. The output has to be inside its window after the pass device has settled, which is fast on a 1 microfarad capacitor at light load and slower on a large capacitor at full load. A downstream rail that enables on this pin sees a delay that depends on the load, so the sequence has to be checked at both extremes.

The 18 V input is for transients, not for continuous operation at 500 mA. The regulator is built for a wide input with a small average current. A 15 V to 3.3 V step at 500 mA is 5.85 W inside a six pin body, which no copper area can pass at any sensible ambient.

One microfarad is the stability floor, not the target. The regulator is stable from 1 microfarad and the transient response at 500 mA improves with more. Where the load steps quickly, the capacitor is chosen from the step and the allowed sag rather than from the stability minimum.

When the 500 mA member is the right choice

A rail that idles at a few microamp and wakes to drive a radio, a display backlight or a motor for a few hundred millisecond, where the average current is small but the peak is not.

A chain where a wide input must survive a 15 V transient and the load needs a clean 3.3 V with a power good signal for the next stage.

Where this order code fits

It feeds a 500 mA rail on a 12 V or 15 V bus and gives a power good signal, which is the case when a microcontroller reference and its peripheral rail come up together. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Can the output be set to 12 V? Yes on the adjustable member, up to 17.4 V, as long as the input stays above the output by the dropout. At 500 mA that means 590 mV of headroom, so a 12 V output needs at least 12.6 V in.

What is the difference from the TPS7A24? Current and dropout, 500 mA at 590 mV against 200 mA at 250 mV, plus the power good output on this part. The input range and the quiescent current are the same.

Does the power good output need a pull up? Yes, it is open drain. The pull up value sets the rise time and the current the pin sinks, and it should go to the logic rail of the device that reads it rather than to the regulated output.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.