Contact Us

DRV8848PWPR

Brand: Texas Instruments
Texas Instruments DRV8848PWPR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8848PWPR — Power Management & Signal Chain | Superb Automation

DRV8848PWPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8848PWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8848PWPR: the dual bridge for appliances on a 2000 piece reel

The DRV8848PWPR is a dual H-bridge motor driver in a 16 pin HTSSOP, supplied 2000 pieces on a large tape and reel. The vendor carries the part as ACTIVE and lists two bridges that can drive one or two direct current motors, a bipolar stepper motor or another load, a pulse width modulated interface, a fixed off time chopping scheme per bridge for winding current regulation, up to 2 A per output or 4 A in parallel mode at 12 V and 25 degrees with proper heatsinking, an operating supply of 4 to 18 V, a sleep mode, and protection against undervoltage, overcurrent, short circuit and overtemperature with a fault pin.

The 4 to 18 V range puts this part between the battery drivers and the 40 V industrial ones. It covers a 12 V appliance rail, a 24 V rail is outside, and a two cell pack at 8.4 V is comfortably inside. The parallel mode doubles the current for a single larger motor, which is how a washing machine drain pump and a door lock end up on the same part number.

The DRV8848PWPR rows as the addendum publishes them

Part classDual H-bridge motor driver with fixed off time current regulation
Vendor statusACTIVE for the reel row, Obsolete for the tube row
Supply range4 V to 18 V
Output per bridge2 A at 12 V and 25 degrees with heatsinking
Parallel mode4 A
Trip voltage500 mV at a 3.3 V reference, 100 per cent current step
Sense amplifier gain6.6 volts per volt, reference only
Reference input range1 V to 3.3 V, operational below 1 V with reduced accuracy
Current sense blanking1.8 microseconds
Constant off time20 microseconds
Output dead time200 nanoseconds internal
Rise time60 nanoseconds
Fall time60 nanoseconds
Thermal, junction to case bottom4.7 degrees per watt
InterfacePulse width modulated, with sleep and fault pins
ProtectionUndervoltage, overcurrent, short circuit, overtemperature
BodyHTSSOP, 16 pins, 5.00 by 6.40 millimetres
Reel rowDRV8848PWPR, 2000 pieces, large tape and reel
Tube rowDRV8848PWP, Obsolete
MarkingDRV8848 on the body
Moisture levelLevel 3 at 260 degrees, 168 hour floor life
TemperatureMinus 40 to plus 85 degrees
Lead finishNickel palladium gold, tin on one row

The lead finish column is split on this part: the plain reel row carries both a nickel palladium gold and a tin finish in the vendor table, while the A and B rows carry the gold finish only. A customer with a whisker policy or a solder joint requirement in a specification should name the finish on the order rather than accept whichever is in stock, because the same orderable string can arrive with either plating.

What the electrical table fixes

The trip voltage of 500 mV at a 3.3 V reference and the 6.6 volts per volt sense gain are two ways of describing the same comparator, and the sense resistor sets the current: 0.5 V divided by the resistor is the trip current, so 0.25 ohm gives 2 A and 0.125 ohm gives 4 A. At 4 A in parallel mode the resistor dissipates 2 W, which is a resistor in a power package rather than a 0603, and that is a board area item that is easy to forget when the current is doubled.

The fixed 20 microsecond off time is long compared with a modern switching regulator and it is deliberate, because the current ripple in a motor winding at 20 microseconds is small and the switching loss is low. A customer who expects a quiet drive at low current will hear the chopping at about 50 kHz from the winding, and a customer who needs a silent drive needs a different scheme rather than a different value.

The 4 V minimum supply is lower than the rest of the family and it makes the part usable on a 5 V rail with margin. The 18 V maximum rules out a 24 V appliance rail, which is the single most common mismatch in an enquiry for this class. A customer who has a 24 V door lock and a 12 V pump on one board needs two drivers rather than one part number.

Where the body fits on a board

The 16 pin HTSSOP at 5.00 by 6.40 millimetres is the only body offered in production, and the 4.7 degrees per watt junction to case bottom is the number that matters because the pad is the path. That figure is a case to board number, not a junction to ambient number, so the board thermal resistance has to be added before the die temperature is known. A customer who reads 4.7 and assumes it is the whole path will under build the copper.

Two bridges share a supply and a ground, and the return currents meet inside the package as they do in every dual driver. The dead time of 200 nanoseconds is internal, so an external controller cannot create a shoot through by driving both inputs at once, which is a real protection in an appliance where the controller is a low cost part. The fault pin is the diagnostic path and it should be routed even if the first release of the software ignores it. The 20 microsecond off time and the 1.8 microsecond blanking time together set the current ripple, so a customer who changes the inductor without changing either will change the ripple rather than the switching frequency.

What the documents do not publish

The page gives the current at one supply and one ambient and no derating curve, and no junction to ambient thermal resistance at all, only the case to board figure. It gives no curve of on resistance against supply voltage, which matters because the bridge is specified at 12 V and a 5 V appliance rail has a higher resistance. Those numbers are in the electrical table and the typical characteristics.

The page also does not print the sense resistor equation on the product page, only the trip voltage and the gain. A customer who copies a 0.1 ohm resistor from another driver gets 5 A of trip current on a 2 A part, and the overcurrent protection becomes the only limit. That is a board value that has to be computed rather than copied.

Second source and long term availability

Dual bridges for appliances are made by several vendors and the pin out and the interface differ, so a cross is a board change. The supply range and the parallel mode are the two items to match. The pin to pin cross reference page sets out the comparison, and the how to verify a drop in replacement page covers the bench work.

The tube row is obsolete and only the 2000 piece reel is live, so a pilot build is served from a cut reel. The lead finish split on the same string is the other thing to watch, because a material declaration written against one finish and a delivery in the other is a documentation non conformance rather than a functional one, and it still holds up a line.

What to send with an enquiry

Send the exact string, the quantity and the date. State the supply rail, the current per motor and whether the parallel mode is used, because the sense resistor and the dissipation both change. State the lead finish you need if the specification names one. Say which finish your material declaration names, since the same string can arrive either way.

Say whether the two motors run together or in sequence, since the 2 A per bridge is a thermal figure as much as an electrical one. The BOM scrubbing page explains how we reconcile a line like this against the build before a schedule is confirmed.