VNH5019ATR-E
Product Specifications
VNH5019ATR-E — Integrated Motor Driver / Smart Power Switch by STMicroelectronics
The VNH5019ATR-E is an STMicroelectronics integrated motor driver / smart power switch in MultiPowerSO-30 for automotive and industrial actuator control applications.
Part Number Decoded — Field by Field
| Field | Value | Meaning |
|---|---|---|
| VNH5019ATR-E | Full Part Number | STMicroelectronics Motor Driver / Power Switch |
Quick Specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Part Number | VNH5019ATR-E |
| Package | MultiPowerSO-30 |
| Type | Integrated Motor Driver / Smart Power Switch |
| Qualification | Automotive AEC-Q100 / Industrial |
Product Overview
The VNH5019ATR-E is an STMicroelectronics integrated motor driver / smart power switch in MultiPowerSO-30 package. Featuring ST's VIPower technology with monolithic integration of power MOSFETs, gate drivers, and protection/diagnostic circuitry, it simplifies motor control and high-side/low-side switching designs with reduced BOM count and enhanced reliability.
Key Features & Benefits
VIPower Monolithic Integration — Power + Control in One Package
ST's VIPower technology integrates N-channel power MOSFETs, gate drivers, charge pump, and comprehensive protection circuitry on a single die — eliminating external MOSFETs, bootstrap diodes, and sense resistors.
Comprehensive Protection & Diagnostics
Built-in overcurrent, overtemperature (thermal shutdown), undervoltage lockout, and load-dump protection with diagnostic feedback (current sense output, fault status flag) enables self-protecting designs suitable for safety-critical and autonomous systems.
Automotive-Grade Robustness
Designed to withstand harsh automotive and industrial environments including load dump, reverse battery, and extended temperature range for reliable operation in drone payload systems, robotics, and vehicle applications.
Target Applications
Drone Payload & Actuator Control
Drives brushed DC motors, solenoids, and resistive/inductive loads in drone gimbal systems, payload release mechanisms, landing gear actuators, and auxiliary power switching.
Automotive Body & Powertrain
Targets automotive applications including throttle control, EGR valves, HVAC actuators, mirror folding, headlamp leveling, and relay/lamp drivers — all requiring AEC-Q100 qualification.
Industrial Automation & Robotics
Powers motor control, valve actuation, and power distribution in industrial robots, conveyor systems, automated guided vehicles (AGVs), and factory automation equipment.
Frequently Asked Questions
What protection features does the VNH5019ATR-E include?
The VNH5019ATR-E features overcurrent protection, overtemperature shutdown, undervoltage lockout, and diagnostic feedback — ensuring robust, self-protecting operation in demanding environments.
Is external current sensing required?
No. The integrated current-sense output provides proportional load current feedback, eliminating the need for external shunt resistors and differential amplifiers.
What is the minimum order quantity (MOQ)?
Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes.
Request a Quote
SUPERB Automation supplies genuine STMicroelectronics VNH5019ATR-E with full traceability and batch-level QA documentation. Contact us with your target quantity and delivery date — we'll respond with a detailed quotation within 24 hours.
VNH5019ATR-E: a 30 A bridge in MultiPowerSO-30 with a current sense pin
VNH5019ATR-E is an automotive full bridge motor driver in the MultiPowerSO-30 body, on tape and reel. It carries 18 milliohm typical on resistance per leg, a 30 A output current rating and a 41 V supply ceiling, and it adds a dedicated current sense output and a charge pump for reverse polarity protection on top of the protection set the smaller bridges carry. The exposed die pads in the package are what allow 30 A in a body that still fits a body control module.
The sense output is the difference between this string and a plain bridge. The CS pin delivers a current proportional to the motor current whenever CS_DIS is driven low or left open, so the controller can measure torque or detect a stall without an external shunt. On a seat or window motor that reading is often the only diagnostic the module has.
Figures come from the VNH5019A-E data sheet read this round, which prints the 18 milliohm per leg, the 30 A output current, the 41 V maximum supply, PWM to 20 kHz and the AEC-Q100 qualification on the first page.
The operating window
| Function | Automotive full bridge motor driver, two high side and two low side switches |
| On resistance | 18 milliohm typical per leg |
| Output current | 30 A |
| Maximum supply | 41 V |
| PWM | Up to 20 kHz |
| Logic inputs | 3 V CMOS compatible, INA and INB for direction and brake |
| Current sense | CS pin, proportional output, gated by CS_DIS |
| Diagnostics | DIAGA and DIAGB digital feedback through the enable pins |
| Protections | High side and low side thermal shutdown, cross conduction lockout, current limitation, undervoltage and overvoltage shutdown |
| Supply faults covered | Loss of ground and loss of supply |
| Reverse polarity | Charge pump output for an external network |
| Package | MultiPowerSO-30 with exposed die pads, ECOPACK |
| Qualification | AEC-Q100 |
Conduction loss at 18 milliohm
At 18 milliohm per leg, 10 A costs 1.8 W per leg and 20 A costs 7.2 W per leg, with two legs conducting whenever the bridge drives. At the 30 A rating the figure is 16.2 W per leg, which no package can hold continuously in a closed module. The 30 A number is the switch capability, and the continuous current is decided by the exposed pads, the copper they sit on and the air around them.
The MultiPowerSO-30 body conducts heat through the die pads into the board, so the copper under the package is a thermal component in the same sense as the silicon. A board with a solid plane under the pads and vias into an inner layer will carry several times the current of one that connects only the pins.
The sense pin in practice
The CS output is a current mirror, so the controller converts it with a resistor to ground. Two details decide whether the reading is usable: the mirror ratio and its tolerance over temperature, and the blanking window after a direction change, because the bridge current reverses and the sense path needs time to settle. A controller that samples during the reversal sees a negative or zero reading and can mistake it for a stall.
CS_DIS turns the sense off, which is useful when the pin shares an analog input with another channel. The pin also has a fault behaviour, so the firmware should treat an out of range value as a fault rather than as a current.
Reverse polarity and the harness
The charge pump output drives an external MOSFET gate so the module survives a reversed battery connection without a series diode in the motor path. The alternative, a blocking diode in the supply, drops voltage and heats up at 30 A, which is why the charge pump approach is used in this class of bridge.
We supply the string for automotive builds and check the reel and the date code at goods in. The power management cross reference page lists the bridge strings we compare when a customer needs the same footprint at a different current, and the PCBA test coverage strategy page describes how we plan the functional test for a motor output, including the sense path, at the assembly stage.
For builds that must show which lot went onto which serial number, the component traceability report service records the reel and the date code against the finished board.
Three questions buyers ask about this string
Is 30 A a continuous rating? It is the switch current rating. Continuous current in a module is set by the thermal path, and at 18 milliohm the loss at 30 A is 16.2 W per leg, which needs a serious heatsink path.
Can the sense pin drive an ADC directly? It is a current output, so it needs a resistor to ground and a filter before the converter. Feeding it into a high impedance input without the resistor gives a rail stuck reading.
Does it work at 24 V? The 41 V ceiling covers a 24 V rail with a load dump clamp, but the load current has to be rechecked because the switching loss and the motor current at 24 V are both higher.