VN5T006ASPTR-E
Product Specifications
VN5T006ASPTR-E — Integrated Motor Driver / Smart Power Switch by STMicroelectronics
The VN5T006ASPTR-E is an STMicroelectronics integrated motor driver / smart power switch in PowerSO-10 for automotive and industrial actuator control applications.
Part Number Decoded — Field by Field
| Field | Value | Meaning |
|---|---|---|
| VN5T006ASPTR-E | Full Part Number | STMicroelectronics Motor Driver / Power Switch |
Quick Specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Part Number | VN5T006ASPTR-E |
| Package | PowerSO-10 |
| Type | Integrated Motor Driver / Smart Power Switch |
| Qualification | Automotive AEC-Q100 / Industrial |
Product Overview
The VN5T006ASPTR-E is an STMicroelectronics integrated motor driver / smart power switch in PowerSO-10 package. Featuring ST's VIPower technology with monolithic integration of power MOSFETs, gate drivers, and protection/diagnostic circuitry, it simplifies motor control and high-side/low-side switching designs with reduced BOM count and enhanced reliability.
Key Features & Benefits
VIPower Monolithic Integration — Power + Control in One Package
ST's VIPower technology integrates N-channel power MOSFETs, gate drivers, charge pump, and comprehensive protection circuitry on a single die — eliminating external MOSFETs, bootstrap diodes, and sense resistors.
Comprehensive Protection & Diagnostics
Built-in overcurrent, overtemperature (thermal shutdown), undervoltage lockout, and load-dump protection with diagnostic feedback (current sense output, fault status flag) enables self-protecting designs suitable for safety-critical and autonomous systems.
Automotive-Grade Robustness
Designed to withstand harsh automotive and industrial environments including load dump, reverse battery, and extended temperature range for reliable operation in drone payload systems, robotics, and vehicle applications.
Target Applications
Drone Payload & Actuator Control
Drives brushed DC motors, solenoids, and resistive/inductive loads in drone gimbal systems, payload release mechanisms, landing gear actuators, and auxiliary power switching.
Automotive Body & Powertrain
Targets automotive applications including throttle control, EGR valves, HVAC actuators, mirror folding, headlamp leveling, and relay/lamp drivers — all requiring AEC-Q100 qualification.
Industrial Automation & Robotics
Powers motor control, valve actuation, and power distribution in industrial robots, conveyor systems, automated guided vehicles (AGVs), and factory automation equipment.
Frequently Asked Questions
What protection features does the VN5T006ASPTR-E include?
The VN5T006ASPTR-E features overcurrent protection, overtemperature shutdown, undervoltage lockout, and diagnostic feedback — ensuring robust, self-protecting operation in demanding environments.
Is external current sensing required?
No. The integrated current-sense output provides proportional load current feedback, eliminating the need for external shunt resistors and differential amplifiers.
What is the minimum order quantity (MOQ)?
Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes.
Request a Quote
SUPERB Automation supplies genuine STMicroelectronics VN5T006ASPTR-E with full traceability and batch-level QA documentation. Contact us with your target quantity and delivery date — we'll respond with a detailed quotation within 24 hours.
VN5T006ASPTR-E: a 6 milliohm high side driver for 24 V loads
VN5T006ASPTR-E is a single channel automotive high side driver in the PowerSO-10 body, on tape and reel, rated for a 24 V system. It holds 6 milliohm typical on resistance, a 115 A typical current limit, an operating range of 8 V to 36 V and a 58 V transient ceiling. The low resistance is what allows a 24 V load of tens of amps to be switched without an external contactor.
The 58 V transient rating is the key difference from the 12 V family. A 24 V rail with a load dump clamp sits well above 40 V, so the 40 V parts cannot be used there even though the steady current may be small. The operating floor of 8 V also matters, because a 24 V system that sags during a start event drops below the 12 V family's floor and would reset.
Figures come from the VN5T006ASP-E data sheet read this round, which prints 58 V transient, 8 V to 36 V operating, 6 milliohm per channel, 115 A current limit and 2 microamp off state supply current.
The electrical window
| Function | Single channel high side driver with analog current sense, 24 V system |
| Maximum transient supply | 58 V |
| Operating range | 8 V to 36 V |
| On resistance | 6 milliohm typical per channel |
| Current limit | 115 A typical |
| Off state supply current | 2 microamp typical with all loads connected |
| Logic levels | 3.0 V CMOS compatible |
| Diagnostics | Proportional load current sense, off state open load, short to supply |
| Fault handling | Overload and short to ground latch off, thermal shutdown latch off, fault reset standby pin |
| Supply faults covered | Loss of ground, loss of supply, undervoltage shutdown, overvoltage clamp |
| Package | PowerSO-10, tube and tape and reel order codes |
| Qualification | AEC-Q100 |
Loss at 6 milliohm and the current that follows
At 6 milliohm, 20 A costs 2.4 W and 50 A costs 15 W. The first figure is a comfortable PowerSO-10 load with a decent copper area, the second is not, which is why the 115 A limit is a fault rating. For a 24 V heater or a 24 V motor that draws 15 A to 20 A, the part is a direct fit and the switch loss is a small part of the budget.
The sense output is a current mirror, so the controller converts it with a resistor to ground. At 115 A the mirror output is at its largest, and the sense resistor has to be chosen so the resulting voltage stays inside the converter input range at the highest load, not only at the nominal one. That is the calculation we check first when a customer sends the sense network drawing for review, because a resistor sized at nominal load clips at inrush.
24 V systems and the parts that do not fit
Trucks, buses, agricultural machines and industrial vehicles run 24 V rails with a load dump that reaches far above the steady voltage. The 58 V transient rating covers that with a clamp, and the 8 V operating floor covers a cold start. A 40 V part from the 12 V family will work on the bench and fail in the field, which is the substitution we refuse when a BOM line is changed without the rail being checked.
The other consideration is the FR_Stby pin, which resets a latched fault and holds the device in standby. Its state at power up decides whether the channel comes on or stays off, so it belongs in the harness and software review rather than in a note.
Supply position
We hold this string for vehicle and industrial builds on 24 V, and we check the reel and the date code at goods in. The power management cross reference page lists the 24 V high side family beside the 12 V family so the rail is checked before the part is chosen. Where a customer is reducing the number of approved suppliers, the vendor consolidation page describes the route, and the date code management page covers how older stock is kept away from a line with a shelf life rule.
Three questions buyers ask about this string
Is the 58 V figure a continuous rating? No. It is the maximum transient supply. Continuous operation is 8 V to 36 V.
Can it replace a 40 V part on a 12 V rail? It can electrically, but the 8 V floor and the sense ratio differ, so the firmware and the sense network both have to be reviewed.
Does the tube code exist? Yes, the product summary prints both the tube and the tape and reel order codes for the PowerSO-10 body.