L78M05ABDT-TR
Product Specifications
L78M05ABDT-TR — 5V, 500mA Fixed Positive Voltage Regulator by STMicroelectronics
The L78M05ABDT-TR is STMicroelectronics' 5v, 500ma fixed positive voltage regulator. Supplied by SUPERB Automation.
Part Number Decoded — Field by Field
| Field | Value | Meaning |
|---|---|---|
| L78M05ABDT-TR | Full Part Number | 5V, 500mA Fixed Positive Voltage Regulator |
Quick Specifications
| Parameter | Value |
|---|---|
| Output Voltage | 5V Fixed |
| Output Current | 500mA |
| Input Voltage Range | Up to 35V |
| Line Regulation | 100mV max |
| Load Regulation | 100mV max |
| Package | TO-252 (DPAK) |
| Protection | Thermal, SOA, short-circuit |
Product Overview
5V, 500mA Fixed Positive Voltage Regulator from STMicroelectronics. Supplied by SUPERB Automation with full traceability and batch-level QA documentation.
Key Features & Benefits
Wide Input Range Up to 35V — Direct Battery Operation
With an input voltage range of up to 35V, the L78M05ABDT-TR can be powered directly from 3S–8S LiPo flight batteries without a pre-regulator, simplifying drone power distribution while providing a clean 5V rail for flight controller and servo power.
Rugged Protection — Thermal, SOA, and Short-Circuit
Comprehensive internal protection includes safe operating area (SOA) limiting, thermal shutdown, and output short-circuit protection — ensuring reliable operation even when cooling airflow is restricted in compact drone enclosures.
TO-252 DPAK Package — Compact SMD Power Regulation
The TO-252 (DPAK) surface-mount package provides excellent thermal performance in a PCB-friendly footprint, enabling efficient heat dissipation through copper pours for continuous 500mA operation without bulky heatsinks.
Target Applications
Drone Flight Controller 5V Rail
Provides the primary 5V bus for flight controllers that require regulated 5V input, powering the on-board 3.3V LDO cascade, RC servo rails, and 5V peripherals including GPS receivers and telemetry radios.
5V Servo & Actuator Power in Fixed-Wing UAVs
Delivers clean 5V for RC servo arrays (aileron, elevator, rudder, flaps) in fixed-wing and VTOL drone autopilot systems, ensuring stable control surface actuation without voltage sag under transient loads.
Industrial & Automotive 5V Regulation
Widely used in industrial control, automotive electronics, and test equipment where a robust, well-protected 5V supply is needed from unregulated or noisy input rails up to 35V.
Frequently Asked Questions
What is the difference between L78M05ABDT-TR and L78M05CDT-TR?
The AB variant offers ±2% output voltage tolerance vs ±4% for the C version. The AB also has slightly better line/load regulation. For drone applications where sensor accuracy depends on stable supply voltage, the AB variant is recommended.
Does the L78M05ABDT-TR need a heatsink?
For currents below 200mA at moderate input voltages, the DPAK package can dissipate heat through PCB copper pours alone. Above 300mA or with high input-output differential (>15V), additional copper area or a small SMD heatsink is recommended.
Request a Quote
SUPERB Automation supplies genuine STMicroelectronics L78M05ABDT-TR with full traceability and competitive lead times. Contact us with your target quantity — we'll respond with a quotation within 24 hours.
L78M05ABDT-TR: a 500 mA 5 V regulator in DPAK, A grade at 2 percent
L78M05ABDT-TR is the 5 V member of the L78M precision regulator family from STMicroelectronics, in the DPAK body, tape and reel. The family delivers 0.5 A, holds 2 percent in the A and AB grades and 4 percent in the C grade, and adds output transition safe operating area protection to the current limit and thermal shutdown that the smaller L78L already has. The document that covers it is DS0425, revision 24, dated September 2020.
The difference from the L78L is not only current. A 500 mA regulator in a DPAK has a thermal path through the tab to the board, so the package becomes part of the electrical decision. The same die in a TO-220 with a heatsink will carry more power than the DPAK can, and the DPAK will carry more than a SOT-89 with the same copper area. The order code letter DT is the DPAK, and the family also ships in TO-220, TO-220FP and IPAK.
The 5 V window and the rest of the table
| Output voltage at 25 degrees, A grade | 4.9 to 5.1 V, plus or minus 2 percent |
| Output voltage over load, A grade | 4.8 to 5.2 V, 5 to 350 mA, input 7 to 20 V |
| Output current | 0.5 A with adequate heat sinking |
| Test input voltage | 10 V at 350 mA for the 5 V table |
| Line regulation | 50 mV maximum, 7 to 25 V at 200 mA |
| Load regulation | 100 mV maximum, 5 to 500 mA |
| Supply voltage rejection | 62 dB typical over 10 Hz to 100 kHz |
| Output voltage drift | minus 0.5 millivolts per degree typical |
| Protections | Current limit, thermal shutdown, output transition safe operating area |
| Packages in the family | TO-220, TO-220FP, DPAK, IPAK |
| Temperature range | Extended range guaranteed, minus 40 to plus 125 degrees for the AB grade |
| Package on this code | DPAK, tape and reel |
Reading the grade letters before the price
Three codes look almost identical and behave differently. The A grade holds plus or minus 2 percent, so 4.9 to 5.1 V at room temperature. The C grade holds plus or minus 4 percent, so 4.8 to 5.2 V. The AB grade keeps the 2 percent window and extends the guarantee down to minus 40 degrees. A quote that compares the A and C codes without naming the grade is comparing two different guarantees, and on a 5 V rail that feeds a CAN transceiver the 100 mV difference at the edge is the difference between a passing and a marginal circuit.
Dissipation is the second decision. From a 12 V input at 300 mA the part drops 7 V and dissipates 2.1 W, which no DPAK will hold at a 70 degree ambient without a copper pour under the tab and a via field into an inner layer. From a 9 V input at the same current it dissipates 1.2 W, which a DPAK on a decent pad will carry. The input rail, not the regulator, decides whether this part is a good choice.
Where it is used, and the pages that follow on
The part appears as the 5 V rail of an industrial controller, the logic supply of a motor drive card, and the housekeeping rail of a radio unit where a switching regulator would put its ripple on the receive band. Related pages are power management cross reference, pin to pin cross reference for the 78M series alternatives, and one stop BOM sourcing for the rest of the rail.
Questions buyers ask on this code
Whether a 78M can replace a 78L is the usual first question, and the answer is no without a board change, because the packages and the pin order differ. The second is whether the DPAK needs a heatsink, and the answer is that the copper under the tab is the heatsink, so the pour area and the via count belong in the drawing. The third is the tape width and reel quantity on the TR suffix, which matters on a line that runs the part at a few hundred pieces a week.