DRV8833PWPR
Product Specifications
DRV8833PWPR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8833PWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8833PWPR: the dual bridge for two small motors on a 2000 piece reel
The DRV8833PWPR is a dual H-bridge motor driver in a 16 pin HTSSOP, supplied 2000 pieces on a large tape and reel. The vendor carries the part as ACTIVE and lists two H-bridges that can drive two direct current motors or one bipolar stepper, an on resistance of 360 milliohms across the high and low side devices, an output of 1.5 A root mean square and 2 A peak per bridge in the HTSSOP and QFN bodies, 500 mA root mean square and 2 A peak in the small outline body, a parallel mode that gives 3 A root mean square and 4 A peak, an operating supply of 2.7 to 10.8 V, pulse width modulated winding current regulation and limiting, a sleep mode and protection against overcurrent, short circuit, undervoltage and overtemperature.
The 2.7 to 10.8 V supply is the defining limit and it is deliberately narrow. This is a part for battery products, toys, printers and small mechatronics, not for a 24 V industrial machine. A customer who has a 12 V rail and a 12 V motor cannot use it, and a customer who has a two cell lithium pack at 6 to 8.4 V is exactly inside the range. The parallel mode is what makes the small part usable for a single slightly larger motor.
The DRV8833PWPR rows as the addendum publishes them
| Part class | Dual H-bridge motor driver with current regulation |
| Vendor status | ACTIVE for the HTSSOP and QFN reels, Obsolete for the tube |
| Data sheet | SLVSAR1E, January 2011, revised July 2015 |
| Supply range | 2.7 V to 10.8 V |
| On resistance, high plus low side | 360 milliohms |
| Output, HTSSOP and QFN | 1.5 A root mean square, 2 A peak per bridge |
| Output, small outline | 500 mA root mean square, 2 A peak per bridge |
| Parallel mode | 3 A root mean square, 4 A peak on the HTSSOP and QFN |
| Parallel mode, small outline | 1 A root mean square, 4 A peak |
| Current regulation | Pulse width modulated, with limiting |
| Sleep mode | Dedicated pin, low quiescent current |
| Protection | Overcurrent, short circuit, undervoltage lockout, overtemperature |
| Fault reporting | Fault output pin |
| Body, HTSSOP | 16 pins |
| Body, small outline | 16 pins |
| Body, QFN | 16 pins |
| Reel row, HTSSOP | DRV8833PWPR, 2000 pieces, large tape and reel |
| Reel row, small outline | DRV8833PWR, 2000 pieces, large tape and reel |
| Reel row, QFN | DRV8833RTYR, 3000 pieces, large tape and reel |
| Tube row | DRV8833PW, Obsolete |
| Small QFN reel | DRV8833RTYT, Obsolete |
| Marking, HTSSOP | DRV8833 on the body |
| Marking, small outline | 8833PW on the body |
| Moisture level | Level 3 at 260 degrees, 168 hour floor life |
| Temperature | Minus 40 to plus 85 degrees |
Three bodies with three different current ratings share one die, and the small outline body gives a third of the root mean square current of the others. A customer who moves a board from the HTSSOP to the small outline to save height loses two thirds of the continuous current, and the peak rating stays the same, which makes the loss easy to miss. The marking on the small outline body is the only way to tell the two apart after assembly.
What the electrical table fixes
The 360 milliohm bridge is the lowest on resistance in this batch, and at 1.5 A it drops 0.54 V and dissipates 0.81 W. That is why the part runs two small motors from a battery without a heatsink, and why the 2 A peak is a short pulse rating. Two bridges at once double the dissipation, so a robot with two motors driving at the same time is at 1.6 W, which in a 16 pin body needs a copper pad rather than a trace.
The narrow supply range has a second consequence that the feature list does not spell out. Below 5 V the on resistance rises and the maximum output current falls, so a 3.3 V system cannot get 1.5 A from the bridge even though the supply is inside the range. The vendor's table footnote states this, and it is the reason a 3.3 V motor drive usually runs at a lower current than the headline or uses the parallel mode.
The current regulation is a chopping loop with an external sense resistor, and the value sets the limit. A bridge without a sense resistor runs as a plain switch and relies on the overcurrent protection, which is a fault limit rather than a control loop. A customer who wants torque control needs the sense resistor and the reference, and a customer who only wants on and off does not.
Where the body fits on a board
The 16 pin packages are all small enough to sit next to the motors, which is where a motor driver should be, because the motor leads carry switching current and a long lead radiates. The HTSSOP and the QFN have exposed pads and the small outline does not, so the small outline is the body for a low current build in a low profile product, and the other two are for anything that needs the continuous current.
Two bridges in one package share a supply and a ground, so the return currents of both motors meet inside the package. A board that grounds one motor to the chassis and the other to the board creates a loop through the part, and the symptom is an overcurrent fault on one channel when the other is loaded. Both motor returns belong on the same ground plane, close to the package.
What the documents do not publish
The page gives the on resistance at one condition and the current at three bodies, but no curve of current against supply voltage, which is the number a battery product needs as the pack discharges. It gives no thermal resistance in the summary and no safe operating area. Those are in the thermal table and the typical characteristics of the document.
The page also does not print the sense resistor value or the reference arrangement for the current regulation. A customer who wants to limit the stall current has to read the application section for the equation and then choose a resistor, and a copy of a value from another driver gives a different limit because the gain differs between families.
Second source and long term availability
Dual bridges for battery products are made by several vendors and the pin out is not standard, so a cross is a board change. The on resistance and the supply range are the two items to match. The pin to pin cross reference page sets out what we compare, and the how to verify a drop in replacement page covers the bench checks.
The tube row and the small QFN reel are already obsolete while the large reels are live, which is the pattern across the family. A customer who is buying the tube has a conversion to make and the conversion is to a reel or to a different body. The HTSSOP row is the safest of the three for a long programme because it has the highest current in the most common feeder format.
What to send with an enquiry
Send the exact string, the body, the quantity and the date. State the supply range and the current per motor, because the small outline body cannot deliver the same current as the others. State whether the two motors run at the same time, since that decides the dissipation.
Say whether the current regulation is used or whether the bridge runs as a plain switch, because a sense resistor changes the board and the tuning. State the sleep behaviour you need as well, since the sleep pin is the only way to reach the microamp range. The BOM scrubbing page explains how we reconcile a line like this against the build before a schedule is confirmed.