Contact Us

DRV8323SRTAR

Brand: Texas Instruments
Texas Instruments DRV8323SRTAR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8323SRTAR — Power Management & Signal Chain | Superb Automation

DRV8323SRTAR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8323SRTAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8323SRTAR: Three phase smart gate driver with three current sense amplifiers and a SPI port in a 40 pin WQFN

DRV8323SRTAR is a 6 V to 60 V three phase gate driver in the 40 pin RTA body that drives six external N channel MOSFETs, sets its gate current anywhere from 10 mA to 1 A source and 20 mA to 2 A sink, and carries three current sense amplifiers plus a SPI interface in a WQFN-40 body of 40 pins. The DRV8323S is the SPI member of the DRV832x family with three current sense amplifiers and no integrated buck converter. It runs from 6 V to 60 V, holds 100 percent duty cycle through a charge pump, accepts 1.8 V, 3.3 V and 5 V logic, and exposes slew rate, gain, dead time and protection thresholds as register settings rather than as resistor choices. An internal 3.3 V regulator supplies up to 30 mA to the rest of the board.

Order code and package

Order codeDRV8323SRTAR
Phases3, six external N channel MOSFETs
Operating voltage6 V to 60 V
Peak source current10 mA to 1 A, adjustable
Peak sink current20 mA to 2 A, adjustable
Current sense amplifiers3
InterfaceSPI plus three PWM input modes
Integrated bucknone on the S variant
Logic levels1.8 V, 3.3 V and 5 V
Package40 pin WQFN, RTA body, 6 mm by 6 mm by 0.75 mm

Electrical parameters that decide the application

Charge pump capacitor, CPH to CPL47 nF, rated for the motor supply
Charge pump output capacitor, VCP to VM1 uF, 25 V
Internal regulator output, DVDD3.3 V, 1 uF, 6.3 V, sources up to 30 mA externally
Supply decoupling, VM to PGND0.1 uF ceramic plus at least 10 uF bulk
Duty cycle support100 percent through the charge pump
High side source, transientminus 7 V for 200 ns on SHx
Gate driver supply, transientminus 7 V for 200 ns on GHx
Low side gate supply, transientminus 1.5 V for 200 ns on GLx
Dead timeset by register on the SPI variant
Overcurrent protectionadjustable threshold through the SPI registers

Points to check before this part goes on a BOM

The gate current range is the widest part of this device. One amp of source current into a 100 nC gate charges it to 10 V in about a microsecond, and the same gate at 10 mA takes a hundred times longer, so the five settings span two decades of edge rate. The reason to use the low end is EMI: a 1 A edge into a 10 nH gate loop produces 100 V of inductive kick in a nanosecond, and the resulting ringing appears on the switch node and on the current sense outputs. A 100 mA edge spreads the same charge over 1 us and moves the ringing energy into a band where the filter can absorb it, at the cost of a longer transition and higher switching loss in the external MOSFET.

Holding 100 percent duty cycle needs the charge pump, and the charge pump needs two capacitors that are chosen from the motor supply rather than from a catalogue default. The 47 nF flying capacitor sits between CPH and CPL at the full motor voltage, and the data sheet asks for twice the supply as a rating, so a 24 V system uses a 50 V part. The 1 uF output capacitor between VCP and VM sees the pump output above the rail, which is why it is specified at 25 V. A 16 V part in that position on a 24 V system is a failure that appears only at high duty, when the pump has to hold the high side gate above the rail for the longest part of the period.

Three current sense amplifiers on one die is the reason to pick the S over the R variant, and it changes how the current signal is scaled. The amplifiers are matched on one substrate, so the gain error between phases is a fraction of the error of three separate amplifiers. That matters for a field oriented control loop, which computes the third phase from two measurements and treats any mismatch as an offset in the transform. A 1 percent gain difference between phases shows up as a torque ripple at the electrical frequency, and it is invisible on a scope triggered on one phase.

The internal 3.3 V regulator sources 30 mA, and that budget is shared between the microcontroller, the isolator on the bus side and any sensor on the board. The gate drive itself is not on that budget, because the gate current comes from the motor supply through the charge pump. A 30 mA budget covers a small motor control MCU in run mode and very little else, so a board that adds a second sensor or a radio has to check the number rather than assume the regulator is free. When it runs out the symptom is a DVDD sag at the moment the MCU wakes, which resets the MCU and looks like a firmware fault.

The minus 7 V transient on the source pin for 200 ns is the specification that decides how much parasitic inductance the phase node can have. When the high side device turns off, the phase node falls and the di/dt through the source inductance pushes the node below ground. A 20 A phase current turning off in 20 ns in a 5 nH source path develops 5 V, which is inside the 7 V allowance. Doubling the loop inductance to 10 nH reaches the limit, and the failure mode is not a clean shutdown but a driver that misbehaves on some boards and not on others, depending on the cable length to the motor.

The SPI interface moves the tuning into registers, and that changes the test flow as well as the bill of materials. A hardware variant sets the gain and the gate current with resistors, so the setting is fixed at reflow and visible on the drawing. The S variant boots with default values and takes its settings from the controller, which means a board that has not been initialised runs at the default gate current, and a firmware change can alter the switching behaviour of a board that has already passed EMC. The register map is the document to version alongside the firmware, not alongside the hardware.

The 40 pin RTA body measures 6 mm by 6 mm by 0.75 mm and carries an exposed pad, and almost none of the heat goes through that pad because the power loss is in the six external MOSFETs. What the pad does is provide the return path for the gate currents and the ground reference for the three current sense amplifiers, so the connection to the ground plane decides whether the current signals sit on a quiet reference. A pad connected with two vias is enough for thermals and not enough for the sense amplifiers, which is why the routing guidance in the document asks for a plane rather than a thermal relief.

Where this order code fits

This order code belongs on three phase brushless stages in power tools, e bikes, fans, pumps, robotic joints and light industrial drives, where the controller has to read phase current on all three legs and change gate drive strength between a bench test and a production build. It is also the part chosen when a board has to be tuned after the first board comes back, because the SPI port lets the gate current and the current sense gain move without a component change. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

What is the difference between the S and the R variants? The S variant carries three current sense amplifiers, a SPI port and no buck converter. The R variants add a 600 mA buck regulator and come in hardware and SPI versions with different pin counts and different bodies. The three parts are not interchangeable on one footprint, so a change from one to another is a board revision rather than a part substitution.

Can the gate current be changed in circuit? On the SPI variant yes, through the register that sets the drive strength. On the hardware variant the same setting comes from a resistor, so it is fixed at build. A board that expects to tune the drive strength on the bench should start on the S variant, because tuning the H variant means changing a component and re running any EMC test that depended on the edge rate.

Does 100 percent duty hold at any supply voltage? The charge pump keeps the high side gate above the rail, so the stage can hold the high side device on indefinitely across the 6 V to 60 V range. What changes with voltage is the gate voltage available to the external device, and therefore its on resistance. At the low end of the supply range the gate drive may not be enough to reach the resistance the thermal calculation assumed, so the low line case is the one to check first.

Why are the transient ratings negative on the phase pin? Because that is the direction the parasitic inductance pushes the node when the high side device turns off. The phase node falls below ground by an amount set by the current, the turn off time and the inductance between the source of the high side device and the ground of the driver. The rating is a 200 ns allowance, so a slower turn off with less overshoot and a faster turn off with more both need to be checked against it.

SUPERB holds and sources this driver line against the exact order code, with the reel, date code and country of origin stated on the offer. When a stage has to move to a second part, the Pin to Pin Cross Reference page sets out the checks that separate a working substitute from one that fails on the bench.