AD8021ARZ-REEL7
Product Specifications
AD8021ARZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8021ARZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD8021ARZ-REEL7: 2.1 nV Noise With an External Compensation Pin
The AD8021ARZ-REEL7 is a voltage feedback operational amplifier with 2.1 nV per root hertz voltage noise, 2.1 pA per root hertz current noise, 200 MHz of bandwidth at a gain of minus one and 190 MHz at a gain of minus ten, drawing 6.7 mA from a 5 V supply. Its compensation is external, which is what holds the bandwidth constant from a gain of minus one to a gain of minus ten, and it works from 5 V to 24 V with a disable pin that drops the supply current to 1.3 mA. The order code carries the industrial temperature range, the SO-8 package and a tape and reel quantity.
Custom compensation, and what it costs the board
Most high speed amplifiers are internally compensated for unity gain, which means the bandwidth falls as the gain rises. This part brings the compensation node out, so a single capacitor sets the bandwidth for the gain the stage actually uses. A stage at a gain of minus ten can therefore run the same 190 MHz that a gain of minus one runs, instead of a tenth of it. The cost is a pin, a capacitor and a stability analysis that belongs to the board rather than to the silicon: too small a capacitor gives peaking, too large gives a slow stage, and the value depends on the feedback network and the load capacitance.
| Voltage noise | 2.1 nV per root hertz, 664 nV over a 100 kHz band |
| Current noise | 2.1 pA per root hertz |
| Bandwidth | 200 MHz at a gain of minus one, 190 MHz at minus ten |
| Supply current | 6.7 mA at 5 V, 34 mW, 1.3 mA with the disable pin asserted |
| Distortion | Minus 93 dBc second harmonic at 1 MHz, 22.4 ppm of the fundamental |
| Third harmonic | Minus 108 dBc at 1 MHz, 3.98 ppm |
| Offset voltage | 1 mV maximum, 0.5 uV per degree C drift |
| Supply range | 5 V to 24 V, single or split |
| Package | 8-lead SOIC or MSOP, industrial temperature range |
Noise and distortion in converter bits
A 16 bit converter on a 2 V peak to peak span has a least significant bit of 30.5 uV. The amplifier's noise integrated over 100 kHz is 664 nV, which is 2.2 percent of that bit, so the amplifier is not the limit; integrated over the full 200 MHz of bandwidth the same density gives 29.7 uV, which is a whole bit, and that is the argument for a bandwidth limiting network in front of the converter. Noise density is a per root hertz figure and the band it is integrated over is a choice the board makes.
The distortion figures are more interesting than they look. Minus 93 dBc of second harmonic at 1 MHz is 22.4 ppm of the fundamental, and one 16 bit least significant bit is 15.3 ppm of full scale, so a full scale tone produces a second harmonic about 1.5 bits high. That is adequate for a 14 bit front end and marginal for a 16 bit one, which is why the part is usually specified into 14 bit or 16 bit systems with a signal that does not reach full scale. The 1 mV maximum offset, by contrast, is 32.8 least significant bits at that span, which tells you the part is chosen for its alternating current behaviour and not for its direct current accuracy.
Where the disable pin earns its place
A 1.3 mA disabled state against 6.7 mA enabled is a five times reduction, and on a multi channel instrument it is the difference between a front end that can multiplex into one amplifier and one that needs an amplifier per channel. The pin is also a way to protect the input stage during a range change, and it is fast enough that the settling after enable is a small part of the acquisition window. On a board that measures one channel at a time, this is the reason to choose a part with a disable over a slightly quieter part without one.
The supply range from 5 V to 24 V is wider than most high speed parts, which is what makes the amplifier usable in a 12 V or 15 V signal chain where the extra headroom buys dynamic range. At 24 V the dissipation rises to 161 mW, which an SO-8 handles, and the input stage is specified across that range. A board that runs at 5 V for noise and 15 V for headroom can use the same order code for both, which is worth something in a product family.
Two questions buyers ask
Does it need the external compensation capacitor?
Yes. The compensation node is brought out, so the capacitor is part of the circuit and its value sets the bandwidth and the stability. A board built without it is an oscillator, and a board built with a value copied from another amplifier is a stage with unknown peaking.
Is 1 mV of offset a problem?
At a 2 V peak to peak span it is 32.8 least significant bits of a 16 bit converter, so it is a problem for a direct current measurement and not for an alternating current one. A stage that needs both usually puts the offset correction in the digital domain or uses a chopper stabilised amplifier ahead of this one.
Ordering and supply
The AD8021ARZ-REEL7 is the industrial temperature, SO-8, tape and reel code. Cross references fail on the compensation arrangement and on the supply range, because an internally compensated part with a similar noise figure will have a bandwidth that collapses at the gain the stage needs. The disable pin and the 24 V capability are also not universal across the family.
We hold and source this family for production quantities and for repair lots. Start from the family page for analog mixed signal ICs, check a proposed alternative against the amplifier cross reference, and when the amplifier drives a converter the pairing is checked against the ADC and DAC cross reference so that the settling and the noise are budgeted together rather than separately.
Request Quote — In Stock, 100% New & Original, Full Warranty