AD7124-8BCPZ-RL7
Product Specifications
AD7124-8BCPZ-RL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD7124-8BCPZ-RL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD7124-8BCPZ-RL7: 24 Bits Across 8 Differential Channels, Three Power Modes and the Noise Each One Actually Gives
The AD7124-8BCPZ-RL7 is a complete low power analogue front end for precision measurement: a 24-bit sigma-delta converter with a crosspoint multiplexer for 8 differential or 15 single-ended inputs, a programmable gain stage from 1 to 128, a band gap reference with 10 ppm per degree C maximum drift that draws 70 uA, matched programmable excitation currents, a bias voltage generator that sets the common mode to half the supply, a low side power switch for bridge sensors, burnout detection, an internal temperature sensor and a channel sequencer. Supply is 2.7 V to 3.6 V single ended or plus and minus 1.8 V, power-down current is 5 uA maximum, the package is a 32-lead LFCSP, and the W grade is AEC-Q100 qualified for automotive use.
What separates this part from a plain 24-bit converter is the three power modes. Each mode pairs an output data rate range with a supply current and a noise level, and the pairs are not proportional: the low power mode at 255 uA and 1.17 SPS has 24 nV RMS of noise at a gain of 128, while the full power mode at 930 uA and 9.4 SPS has 23 nV. Eight times the current for eight times the rate and the same noise, which is a useful way to read the table.
At a gain of 128 one LSB is 2.384 nV and the noise is 10 of them
With a 2.5 V reference and a gain of 128 the full scale input is plus or minus 20 mV, so a 24-bit LSB is 40 mV divided by 16.78 million, or 2.384 nV. The 24 nV RMS of the low power mode is 10.1 LSB, which works out to 20.7 noise free bits. The data sheet's 22 noise free bits figure belongs to a gain of 1, where the full scale is plus or minus 2.5 V and the same absolute noise is a smaller fraction of it. Both numbers are true and they describe different configurations, which is the single most common misreading of this part: the 22 bit headline does not survive a gain of 128 with a 20 mV signal.
Twenty microvolts of full scale with 24 nV of noise also fixes the sensor. A 350 Ohm bridge with 2 mV per volt of output at 5 V excitation produces 10 mV at full load, which is half of the plus or minus 20 mV range, so the converter sees 5 million counts across the load. That is 22.3 bits of resolution on the load, which is more than any mechanical bridge can hold. The sensor, not the converter, sets the useful resolution, and the reason to use this part is the integration of excitation, bias and switching rather than the bit count.
| Resolution | 24 bits, up to 22 noise free bits at a gain of 1 |
| Inputs | 8 differential or 15 single-ended or pseudo differential, crosspoint multiplexer |
| Gain | 1 to 128, rail-to-rail inputs above a gain of 1 |
| Low power mode | 255 uA, 1.17 SPS to 2,400 SPS, 24 nV RMS at a gain of 128 |
| Mid power mode | 355 uA, 2.34 SPS to 4,800 SPS, 20 nV RMS at a gain of 128 |
| Full power mode | 930 uA, 9.38 SPS to 19,200 SPS, 23 nV RMS at a gain of 128 |
| Reference | Internal band gap, 10 ppm per degree C maximum, 70 uA |
| Mains rejection | Simultaneous 50 Hz and 60 Hz at 25 SPS single cycle settling, above 80 dB lower |
| Supply | 2.7 V to 3.6 V, or plus and minus 1.8 V, 5 uA in power-down |
| Package and grade | 32-lead LFCSP, minus 40 C to 125 C, W grade AEC-Q100 |
The internal reference is the accuracy limit, not the converter
Ten parts per million per degree C over 125 degrees is 1250 ppm, which on 2.5 V is 3.125 mV. Against a 2.384 nV LSB that is 1.3 million LSB, or 20.7 bits of drift, which is the same order as the converter's own noise. So at 24 bits the internal reference is as large an error as the converter noise, and at 20 bits it is larger. The internal reference is adequate for ratiometric measurements where the same reference feeds the bridge excitation, and an absolute measurement calibrated once at 25 C will drift by 1250 ppm at the temperature extremes unless an external reference is used.
The excitation current sources are where a ratiometric arrangement wins. Driving the bridge from the same reference that sets the converter's full scale cancels the reference drift, because a 1 percent change in excitation produces a 1 percent change in signal and a 1 percent change in full scale, and the digitised ratio does not move. That is the arrangement the internal reference and the matched current sources exist to support, and it is why this part is used in weigh scales and pressure transmitters rather than in absolute voltmeters.
Two questions buyers ask
Can the part scan eight channels and still reject 50 Hz?
Not at the same time. Simultaneous 50 Hz and 60 Hz rejection belongs to the 25 SPS setting with single cycle settling, so a scan of eight channels at 25 SPS per channel takes 320 ms. Above that rate the rejection falls and below it the filter is longer than a cycle. The channel sequencer makes the scan automatic, and the filter setting is per channel, so a system can run the fast channels without rejection and the slow ones with it.
What does the low side power switch do for a bridge?
It removes power from the bridge between conversions, which is the difference between a battery powered transmitter that lasts years and one that lasts months. The bridge current is the dominant load in most of these systems, and switching it off between readings costs a settling time and saves the average current. The switch has to be accounted for in the settling budget, because the bridge needs time to come back after it is re-energised.
Ordering and supply
The BCPZ suffix is the 32-lead LFCSP, lead free, in tape and reel. Substitution traps are the power mode table, the reference drift and the automotive grade. A converter with the same 24 bits and only one power mode cannot trade current for rate, and a part whose internal reference drifts at 30 ppm per degree C loses two bits over the industrial range compared with this one.
We hold and source this family for production and for repair. Start from the analog mixed signal ICs family page, compare a candidate against the ADC and DAC cross reference, and where a substitute has to be qualified on a board that is already built, the order in how to verify a drop in replacement puts the reference and the power modes first.
Request Quote — In Stock, 100% New & Original, Full Warranty