ADA4841-1YRZ-R7
Product Specifications
ADA4841-1YRZ-R7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADA4841-1YRZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADA4841-1YRZ-R7: 2.1 nV of Noise on 1.1 mA, and the 16-Bit ADC It Was Built to Drive
The ADA4841-1YRZ-R7 is a single, unity gain stable, rail-to-rail output amplifier with 2.1 nV per root hertz of voltage noise, 1.4 pA per root hertz of current noise, 7 nV per root hertz at 10 Hz, and a supply current of 1.1 mA typical, 1.5 mA maximum. It runs from 2.7 V to 12 V, has 80 MHz of gain bandwidth at unity gain, 12 V per microsecond of slew rate, 175 ns of settling to 0.1 percent, and 0.3 mV of maximum offset. The output reaches within 50 mV of either rail, the input common mode range extends to the negative supply, the part drives 10 pF with minimal peaking, and it is specified from minus 40 C to 125 C with a power-down pin.
The part is aimed at one job: driving 16-bit and 18-bit successive approximation converters whose input sampling network needs a fast, low noise driver that does not cost 10 mA. The data sheet names the AD7685 and AD7686 as the intended loads. A buyer who reads only the noise figure and puts this amplifier in a 10 mA signal chain is overpaying for speed; a buyer who reads only the current and puts a 1 mA amplifier with 20 nV of noise on a 16-bit converter is losing bits.
What 2.1 nV becomes over a real bandwidth
Two point one nanovolts per root hertz integrated over 100 kHz is 664 nV RMS, which against a 16-bit converter on a 10 V span, where one bit is 152.6 uV, is 0.004 of a bit. The amplifier noise is therefore irrelevant at 16 bits and the 7 nV at 10 Hz is what matters at low frequency, because a 0.1 Hz to 10 Hz band is where a DC instrument actually measures. Over 10 Hz to 100 kHz the noise is dominated by the broadband term and lands near 660 nV, still far below one bit of a 16-bit converter, which is the point of the part: the driver disappears from the error budget at 16 bits and is still small at 18.
The current noise tells the other half of the story. One point four picoamps per root hertz into a 10 kOhm source is 14 nV per root hertz, nearly seven times the voltage noise, so the amplifier is only as quiet as the source resistance allows. Above about 7 kOhm the current noise dominates and the 2.1 nV figure stops describing the circuit. That is why the part suits low impedance sensors and converter drive, and it is why a photodiode transimpedance stage with a 1 MOhm feedback resistor needs a different amplifier even though the voltage noise is excellent.
| Voltage noise | 2.1 nV per root hertz, 7 nV per root hertz at 10 Hz |
| Current noise | 1.4 pA per root hertz, 13 pA per root hertz at 10 Hz |
| Supply current | 1.1 mA typical, 1.5 mA maximum per amplifier |
| Bandwidth | 80 MHz at unity gain, 12 V per us slew rate |
| Settling | 175 ns to 0.1 percent, 17.5 percent of a 1 MSPS period |
| Distortion | Minus 105 dBc at 100 kHz into 2 V peak to peak, 17.4 bits of spurious free range |
| Offset | 0.3 mV maximum, 1.97 LSB of a 16-bit converter on 10 V |
| Output | Within 50 mV of either rail, drives 10 pF, input common mode to the negative rail |
| Supply range | 2.7 V to 12 V, power-down pin |
Settling of 175 ns against a 1 MSPS converter
A converter that samples at 1 MSPS gives the driver 1 us between conversions, and 175 ns of settling to 0.1 percent is 17.5 percent of that window. The remaining 825 ns is margin for the acquisition time of the sampling network, the settling of the reference and any multiplexer in front. On a 250 kSPS part like the AD7685 the window is 4 us and the driver has ten times the margin it needs. The settling figure is specified to 0.1 percent, which is 10 bits of accuracy; a 16-bit converter needs settling to 0.0015 percent, and the data sheet's 175 ns is not that number. The distinction matters when the amplifier is asked to settle a multiplexed step rather than a small signal.
The 12 V per microsecond slew rate bounds the large signal case. At 2 V peak to peak, a sine wave limited by the slew rate reaches 1.91 MHz of full power bandwidth, well below the 80 MHz small signal figure. A 100 kHz signal at 2 V peak to peak needs 1.26 V per microsecond, which is a tenth of the available slew, so the distortion figure of minus 105 dBc at that frequency is a small signal number in slew terms and a real one in linearity terms.
Two questions buyers ask
Is it stable as a unity gain buffer into a converter?
Yes, the part is unity gain stable and the data sheet application is exactly that buffer. What it will not do is drive a large capacitive load directly: 10 pF is the rated load with minimal peaking, and a converter's sampling capacitor plus the board parasitics can exceed that. The usual answer is a small series resistor between the amplifier and the converter pin, which isolates the capacitance and costs a fraction of a bit of settling time.
Can it run from a 12 V rail with a 3 V converter behind it?
It can: the input common mode reaches the negative supply and the output swings within 50 mV of the rails, so a 3 V full scale signal on a 12 V supply is inside the range. The dissipation is 13.2 mW at 1.1 mA and 12 V, which is small, but the headroom means the output stage is far from its rails and the distortion is better than the headline, not worse. The reason to run it at 5 V rather than 12 V is the converter's own input range, not the amplifier.
Ordering and supply
The YRZ suffix is the 8-lead SOIC in tape and reel. Substitution traps are the supply current, the noise at 10 Hz, and the output swing. A part with the same 2.1 nV broadband noise and 20 nV at 10 Hz will read worse in a DC instrument; a part with the same noise and 4 mA of supply current changes the thermal picture in a densely packed board; a part without rail-to-rail output loses the top of the converter's range.
We hold and source this family for production and for repair lots. Start from the analog mixed signal ICs family page, compare a candidate against the amplifier cross reference, and where a substitute has to be qualified on an existing converter board, the order in how to verify a drop in replacement catches the settling and swing differences before the first conversion.
Request Quote — In Stock, 100% New & Original, Full Warranty