LT1964ES5-BYP#TRPBF
Product Specifications
LT1964ES5-BYP#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT1964ES5-BYP#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LT1964ES5-BYP#TRPBF: A Negative Regulator Where the Bypass Pin Buys the Noise
The LT1964 is a 200 mA low noise, low dropout negative regulator that runs from an adjustable minus 1.22 V to minus 20 V or a fixed minus 5 V, with 30 uV RMS of output noise over 10 Hz to 100 kHz, 30 uA of quiescent current and 340 mV of dropout. The -BYP order code exposes the bypass pin, which is where an external capacitor sets the reference noise and therefore the output noise.
Noise, and what the bypass pin does
30 uV RMS against a 16 bit converter on a 5 V range, where one LSB is 76 uV, is 0.39 LSB, so the regulator is not the noise limit for 16 bit work and becomes one at 18 bits. The bypass pin is the lever: a capacitor there filters the internal reference, and the datasheet curves show the noise falling as the capacitor grows, at the cost of a longer start up because the reference has to charge. A board that needs the lowest noise and the fastest start up cannot have both, and the capacitor value is the trade.
Dropout and dissipation in a negative rail
340 mV at 200 mA is 1.7 ohm of equivalent resistance, so a minus 5 V output needs about minus 5.34 V of input to stay in regulation. Deriving minus 5 V from a minus 12 V rail at 100 mA puts 0.7 W in a ThinSOT package, which is more than the package dissipates comfortably; at 200 mA it is 1.4 W and the thermal limiting will act. Negative rails are usually light, which is why the part is rated 200 mA rather than 1 A, and the 3 uA shutdown current makes it usable in a rail that is switched off when a subsystem is idle.
Stability is specified with a 1 uF output capacitor, and the part is stable with aluminium, tantalum or ceramic types, which removes the trap of a ceramic-only requirement on an older board. Quiescent current is well controlled in dropout, so a battery system that sags does not see the regulator itself become the load.
| Output current | 200 mA |
| Output voltage | fixed minus 5 V, adjustable minus 1.22 V to minus 20 V |
| Dropout | 340 mV at 200 mA |
| Noise | 30 uV RMS from 10 Hz to 100 kHz, reduced with a bypass capacitor |
| Quiescent current | 30 uA operating, 3 uA in shutdown |
| Output capacitor | 1 uF, stable with aluminium, tantalum or ceramic |
| Shutdown logic | positive or negative logic options in the family |
| Protection | thermal limiting |
| Package | 5 lead ThinSOT 1 mm, 8 lead 3 mm by 3 mm DFN |
Where it fits
Bipolar analogue front ends that need a quiet negative rail, op amp supplies in instrumentation, audio and sensor conditioning, and any board where the negative rail is derived from a charge pump and then cleaned up. The low dropout is what allows the negative rail to sit close to the positive one without wasting headroom.
Order code and availability
ES5 is the 5 lead ThinSOT body and BYP denotes the variant whose fifth pin is the bypass pin. The regulator family is on the analogue and mixed signal line card.
Common questions
Can the bypass capacitor be omitted? Yes, and the regulator then runs at its nominal noise. Omitting it also shortens start up, so a board that does not need the last few microvolts of noise should leave the pin open rather than fit a token capacitor.
Why is the output current only 200 mA? The package and the dropout together. In a 1 mm ThinSOT body, 200 mA at a 7 V differential is already 1.4 W, so a higher current rating would be a rating the package cannot deliver.
Negative rail parts are grouped on the power management cross reference page, and cost paths are on the component cost reduction page.
Request Quote — In Stock, 100% New & Original, Full Warranty